Abstract:Al-Cu-Mg alloys with spherical structure are prepared using mechanical vibration method. Then, the state of liquid-solid coexistence in the later stage of alloy solidification is obtained by remelting, reproducing the changes in the liquid film and the formation process of hot tearing in the later stage of solidification. Under different initial solidification states, the solidification characteristics and hot tearing behavior of Al-4Cu-1.5Mg- x Y ( x = 0-0.25) alloys are systematically researched. The results indicate that with the increase in Y element, the alloy with spherical microstructure first refines and then coarsens. Under the same remelting conditions, as the Y element increases, the size of the spherical solid first decreases and then increases, but the uniformity of liquid phase distribution gradually increases. When the Y is 0.15 wt.%, the best state of liquid phase uniformly coated spherical solid phase is formed, which is more conducive to eliminating the interference of the solid phase skeleton on the liquid film shrinkage detection in the later solidification stage. Under the same remelting conditions, with the increase in Y element, the crack initiation shrinkage force and corresponding solid fraction of the alloy first increase and then decrease. When the Y element is 0.15 wt.% and the liquid film fraction is 30-33%, the alloy does not exhibit significant hot tearing. The adding appropriate amount of Y element not only reduces the tendency of spherical crystal alloys to form closed zones, but also enhances the feeding ability of the liquid film in the later stage of solidification, thereby reducing shrinkage porosity and the hot tearing tendency of alloys.

Effect of Y and Ce Micro-alloying on Microstructure and Hot Tearing of As-Cast Al–Cu–Mg Alloy

Effect of Ce on Hot Tearing Sensitivity of As-Cast Al-Cu-Mg-Y Alloy

Effect of Ce and Y on Microstructures and Properties of Al-11.0Zn-3.1Mg-1.22Cu-0.1Sr-0.2Zr-0.1Ti Alloy

Effect of Rare Earth Y on Liquid Film of Later Solidification Stage and Hot Tearing of Spherical Al-Cu-Mg Alloy

Effect of rare earth Ce and Y on microstructure and viscosity of ZL114A alloy

Effect of Y on the hot tearing susceptibility of 3Y2O3/Al5Cu composite

Effect of Ce Content on the Microstructure and Mechanical Properties of Al-Cu-Li Alloy

Influence of mixed rare earth elements(Y and Ce) on the microstructure and corrosion behaviour of Mg-4Al-3Ca alloy

Microscopic mechanism of mechanical property improvement of the casted Al-7Si-0.4Mg-0.3Y alloy

Effect of Ca/Al ratio on hot tearing susceptibility of Mg–Al–Ca alloy

Microstructure and Mechanical Properties of Mg-Xy-1.5mm-0.4zr Alloys

Achieving high strength-ductility synergy in dilute Mg-Al-Ca alloy by trace Ce addition

Effect of combined addition of Zr, Ti and Y on microstructure and tensile properties of an Al-Zn-Mg-Cu alloy

Effect of Ce Addition on Modifying the Microstructure and Achieving a High Elongation with a Relatively High Strength of As-Extruded AZ80 Magnesium Alloy

Effect of Ce Addition on the Microstructure, Thermal Conductivity and Mechanical Properties of Mg–0.5Mn Alloys

The effects of substitution of yttrium for Ce-rich mischmetal on the mechanical properties and thermal conductivity of mg–4Al–4Zn–4RE alloy

Effect of rare earth Ce addition on microstructure and mechanical properties of titanium alloy Ti-6Al-4V

Tailoring the microstructure and enhancing the corrosion resistance of extruded dilute Mg-0.6Al-0.5Mn-0.25Ca alloy by adding trace Ce

Effects of yttrium additions on microstructures and mechanical properties of cast Al-Cu-Mg-Ag alloys

Effect of rare earth Ce on the microstructure and mechanical properties of cast Al–7Si alloys

Effects of Zr+Er and Zr+Y on Microstructure and Tensile Properties of Al-Mg-Si-Cu-Mn-Cr Alloys