Antibodies to blood coagulation factors.

S. Shapiro

Clinics in Haematology

Abstract:

What problem does this paper attempt to address?

In-situ dwell-fatigue fracture experiment and CPFE simulation of SLM AlSi10Mg alloy at high temperature

Zhen Wang,Chong Zhao,Jie Wang,Wenwang Wu,Xide Li

DOI: https://doi.org/10.1007/s10704-022-00647-x

IF: 2.635

2022-01-01

International Journal of Fracture

Abstract:The creep-fatigue fracture behavior of selective laser melting (SLM) AlSi10Mg alloy was studied by conducting in-situ scanning electron microscopy experiments at 500 °C. Dwell times of 0, 60 and 120 s were introduced to the tensile-tensile fatigue. The experimental results indicated that the lifetime decreased with lengthening of the dwell time from 0 to 120 s, which closely related to the deformation response behavior of the material. The process of the fracture evolution of the alloy was characterized and analyzed using in-situ scanning electron microscopy images and the fracture morphology. The creep-fatigue fracture mechanism of SLM AlSi10Mg alloy was revealed. Finally, combined with crystal plasticity finite element simulation, the Mises stress, plastic strain and elastic stored energy were used to explain the crack nucleation of SLM AlSi10Mg alloy under fatigue and dwell-fatigue.
In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Junxia Lu,Ling Chang,Jin Wang,Lijun Sang,Shikai Wu,Yuefei Zhang

DOI: https://doi.org/10.1016/j.msea.2017.11.106

2018-01-01

Abstract:This study compares the microstructure and tensile properties of Ti6Al4V components fabricated by laser direct metal deposition (LDMD) additive manufacturing (AM) in the transverse and longitudinal directions. The results show anisotropic tensile properties with the transverse direction having high tensile and fracture strengths and the longitudinal direction having a high elongation and reduction of cross section. The anisotropic mechanical properties are attributed to the anisotropic microstructural distribution. The transverse tensile specimen is composed of short columnar prior-β grains which grow perpendicular to the tensile direction, and have a lamellar structure. Along the β grain boundary, αGB and large α colonies were identified. However, the longitudinal specimen shows that the long β structure is parallel to the tensile axis and that the microstructure is composed of basket-woven α phases with shorter α plates and smaller colony sizes compared with those in the transverse specimen. The fracture mechanism induced by the anisotropic microstructure along the transverse and longitudinal directions was compared by examining the fracture process in real-time using uniaxial in-situ scanning electron microscopy (SEM) tensile testing. The results show that shear fracture, which is caused by the vertical β grain boundaries and large α colonies with long α plates, occurs in the transverse specimen. The shear mode is the main reason behind the enhanced tensile strength and fracture strength due to the high resistance to microcrack propagation. However, in the longitudinal specimens, symmetric necking behavior due to the fine α grains resulted in uniform deformation of the grains on both sides of the grain boundaries, inducing greater elongation.
Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Xiaomiao Niu,Hongyao Shen,Jianzhong Fu

DOI: https://doi.org/10.1016/j.matlet.2018.03.068

IF: 3

2018-01-01

Materials Letters

Abstract:Selective laser melting (SLM) of Mg-Al powder mixture is a promising method to additively manufacture Mg-Al alloy components without using pre-alloyed powder as feedstock. However, the microstructure and consequent tensile properties of SLMed Mg-9 wt%Al powder mixture have not been systematically investigated. In this work, spherical Mg and Al powder with a weight ratio of 91:9 were mixed using ball milling and the mixture was SLMed at different processing parameters. Mg-Al alloy was successfully fabricated and the highest relative density achieved was 95.7%. The results of scanning electron microscopy showed that the microstructure and volume of defects could be controlled by tuning the processing parameters. The highest ultimate tensile strength achieved was 274 MPa, which was comparable to the strength of SLMed pre-alloyed Mg-9 wt%Al as reported in literature. Based on this study, SLM of different Mg powder mixture can be investigated in future. (C) 2018 Elsevier B.V. All rights reserved.
Fatigue and Fracture Behavior of AlSi10Mg Manufactured by Selective Laser Melting: A Review

Z. Jiang,J. Sun,F. Berto,X. Wang,G. Qian

DOI: https://doi.org/10.1134/S102995992304001X

IF: 2.025

2023-08-09

Physical Mesomechanics

Abstract:Selective laser melting (SLM) is one of the most promising metal additive manufacturing technologies. SLMed Al-Si alloys have been widely used in the rail transport, aerospace, and automotive industries. Recently, the fatigue and fracture properties of SLMed Al-Si alloys have attracted considerable attention due to their application in critical load-bearing structures. This review aims to better understand the recent progress on the fatigue and fracture investigations of SLMed Al-Si alloys, especially AlSi10Mg, with emphasis on the effect of defects, heterogeneous microstructure, residual stress, and post-treatment methods. In addition, fatigue and fracture modeling methods are discussed. Finally, the challenges and future research opportunities are prospected.

mechanics,materials science, characterization & testing
In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Qi Ren,Jutian Chen,Junxia Lu,Xiaopeng Cheng,Yuefei Zhang,Ze Zhang

DOI: https://doi.org/10.1016/j.msea.2024.146452

2024-01-01

Abstract:Nickel-based GH3536 alloy exhibits high strength but low ductility when produced by selective laser melting (SLM), which hinders its widespread application in aerospace. This paper employed a 'two-step ' method of heat treatment to optimize the microstructure of the SLM GH3536 alloy and investigated the mechanical properties. Tensile tests were conducted on SLM GH3536 alloy before and after heat treatment at 750 degrees C, using an in -situ high-temperature tensile stage. The relationship between the microstructural evolution and deformation behavior of the alloys was investigated by combining the in -situ tensile experiments and crystal plasticity finite element method (CPFEM). The results suggested that the elongation can be increased by 80% without a significant reduction in tensile strength. The improved elongation is attributed to the complete recrystallization, formation of annealed twins and serrated grain boundaries after heat treatment. The study also investigated the deformation behavior and fracture mode of the alloy before and after heat treatment. Discussion was done on the influence of the microstructure, particularly the twin and serrated grain boundaries on the alloy ' s plastic deformation. This study enhanced the understanding of plastic deformation of SLM GH3536 alloy and provided a valuable reference for the design and post-treatment of superalloy.
Effect of the Boundary Orientation of Melt Pool on Mechanical Property and Fracture Path in Selective-Laser-Melted AlSi10Mg Alloy

Zihao Jiang,Yayun Li,Hang Luo,Baogang Zhou,Yilong Liang,Yu Liang

DOI: https://doi.org/10.1007/s12540-022-01199-4

IF: 3.451

2022-05-29

Metals and Materials International

Abstract:The present work investigated the effect of the boundary orientation of melt pool on the mechanical properties and fracture path in selective-laser-melted AlSi10Mg alloy. The acquired data are beneficial for understanding the influence of the microstructure on mechanical properties. During the alloy's selective laser melting (SLM), the melt pool boundary was almost parallel with the scanning direction, and the grains grew along the building direction. When the load-bearing face was perpendicular to the melt pool boundary, the crack propagation path deflected towards coarse melt pool of the melt pool boundary, reducing the probability of directly crossing the fine melt pool. Otherwise, the cracks would mainly propagate along the melt pool boundary. In the tensile deformation process, coarse melt pool (CMP) was subjected to higher local strain than fine melt pool (FMP) and heat-affected zone (HAZ), and the crack propagated or deflected along the CMP in the melt pool boundary. Therefore, the anisotropy of mechanical properties in SLM AlSi10Mg was mainly ascribed to the CMP density on the load-bearing face. As a weak area, the high proportion of CMP significantly reduced the strength and plasticity of the alloy.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

Mian Huang,Bing Yang,Yuwei Zhou,Xinlong Guan,Yuanzhi Wang,Zhen Liao,Shoune Xiao,Guangwu Yang,Tao Zhu

DOI: https://doi.org/10.1007/s11665-024-09536-x

IF: 2.3

2024-05-11

Journal of Materials Engineering and Performance

Abstract:Selective laser melting (SLM) technology is one of the commonly used technologies in metal additive manufacturing. In this study, AlSi10Mg powder was used as the raw material to form 9 groups of specimens with different combinations of laser power and scanning speeds through the SLM process. Tensile testing, density testing, XRD, LSCM, SEM and EDS analysis were performed to indicate the effects of laser power and scanning speed on density, microstructure and tensile properties of SLM AlSi10Mg alloys were studied. The results show that increasing the laser power and reducing the scanning speed within a certain range can improve the continuity of the formed specimens, and significantly reduce the porosity. For parameter combinations with the same energy density, when laser power and scanning speed are simultaneously increased, the laser power has a dominant effect on increasing the temperature inside the molten pool, leading to more uniform melting of the powder. This can improve both the density and internal porosity distribution, and furthermore produce more precise and uniform microstructures. The relative density and tensile strength of the specimens formed at 225 W/1625 mm/s are 3.6 and 16.5% higher than 135 W/975 mm/s, respectively.

materials science, multidisciplinary
In-situ SEM Investigation on Fatigue Behaviors of Additive Manufactured Al-Si10-Mg Alloy at Elevated Temperature

Zhen Wang,Wenwang Wu,Guian Qian,Lijuan Sun,Xide Li,Josea F. O. Correia

DOI: https://doi.org/10.1016/j.engfracmech.2019.03.040

IF: 5.4

2019-01-01

Engineering Fracture Mechanics

Abstract:In-situ high temperature measurement in a scanning electron microscopy (SEM) environment is an important technique for exploring the microstructure evolution and crack propagation within refractory materials and other advanced alloys. In this paper, in-situ tensile fatigue experiments under SEM environment at room temperature and elevated temperature are performed for studying the fatigue performance and crack propagation process of selective laser melting (SLM) additive manufactured Al-Si10-Mg materials. Firstly, in-situ SLM additive manufactured Al-Si10-Mg fatigue tensile samples are prepared, and micro-CT are employed for the characterization of void defects within SLM additive manufactured Al-Si10-Mg with different laser scanning speeds and laser energy; Secondly, in-situ fatigue experiments are carried out under SEM environment at 25 degrees C, 100 degrees C, 200 degrees C, 300 degrees C, 400 degrees C, 500 degrees C and 600 degrees C, respectively. The fatigue mechanical behaviors, microstructure evolution and crack propagations of as-fabricated Al-Si10-Mg samples are characterized. Finally, micro-CT tomography 3D imaging techniques are employed for exploring the link between SLM defects and fatigue performances.
Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Ping Li,Ruidi Li,Haiou Yang,Tiechui Yuan,Pengda Niu,Minbo Wang,Lanbo Li,Chao Chen

DOI: https://doi.org/10.1016/j.intermet.2020.107008

IF: 4.075

2021-02-01

Intermetallics

Abstract:Selective laser melting (SLM) of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy was systematically investigated in this work, with emphasis on its microstructure evolution, mechanical properties and corresponding metallurgical defects. There is a strong correlation between SLM specimen density and laser parameters; the maximum density of 98.44% was obtained at a volumetric energy density (VED) of 166.67 J/mm3. The formation mechanism of pores is strongly dependent on the laser energy input and the initiation of microcracks is caused by local stress concentration. After SLM, the X-ray diffraction (XRD) peaks of as-printed specimen became broaden compared with powder due to the grain refinement and the shift of diffraction peaks to a higher value due to crystal lattice distortion of the printed specimen. The microstructure exhibits alternately column and fine grain, which is caused by the complex thermal gradient and the existence of Al3(Sc,Zr) particles as nucleating agent. The maximum ultimate tensile strength of 329 MPa and elongation of 9.7% can be obtained at a VED of 166.67 J/mm3. Also, the microhardness increases with the increase of VED owing to the higher cooling rate. This study provides useful guidance for the design of high strength-ductility aluminum alloy without cracking for SLM in the future.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Rong Xu,Ruidi Li,Tiechui Yuan,Pengda Niu,Minbo Wang,Zehuan Lin

DOI: https://doi.org/10.1016/j.jallcom.2020.155372

IF: 6.2

2020-09-01

Journal of Alloys and Compounds

Abstract:Selective laser melting (SLM) is a promising technique for manufacturing 2xxx series Al–Cu alloy parts. However, the metallurgical defects in SLM severely limits their applications. In this work, SLM of a Li and Zr modified Al–Cu–Mg alloy (Al–4Cu–1Li-0.4Mg-0.5Zr) was studied with emphasis on its microstructure, metallurgical defects and hardness. The results show that microstructure is composed of fine equiaxed crystals (0.5–1 μm) and columnar dendrites (10–12 μm in length and 1–2 μm in width) with pronounced pore and crack defects. The geometrically irregular micropores distribute at the boundaries of the molten pool while the regularly round micropores distribute randomly. Cracks were observed growing along the grain boundaries with high angle and almost parallel to building direction, which were mainly caused by local stress concentration in the liquid film. The texture of SLM-processed Al–Cu–Mg–Li–Zr alloy was found in {001}<100> and {001}<310> orientation. The microhardness improved as laser energy density increasing due to the higher cooling rate. This research provides useful guidance in the future for designing crack-free and high strength SLM printed 2xxx series Al alloys.

materials science, multidisciplinary,chemistry, physical,metallurgy & metallurgical engineering
Fatigue performance and crack propagation behavior of selective laser melted AlSi10Mg in 0°, 15°, 45° and 90° building directions

Zhongwei Xu,An Liu,Xishu Wang

DOI: https://doi.org/10.1016/J.MSEA.2021.141141

2021-01-01

Abstract:Abstract In the present work, selective laser melted (SLM) AlSi10Mg samples were used in rotational bending fatigue, scanning electron microscope in-situ fatigue and nanoindentation tests. The effects of building directions (0°, 15°, 45° and 90°) and molten pool boundaries (MPBs) on the fatigue performance and crack propagation behavior of the AlSi10Mg samples were studied. The results indicated that the SLM samples (from 0° to 15° building directions) were in high fatigue performance range. The fatigue fracture parameters (fatigue strength, threshold stress intensity factor range and fracture toughness) of the 0° and 15° samples were higher than those of the 45° and 90° samples. Moreover, the differences of elasticity modulus and hardness between the MPBs and molten pool cores were identified. Under cyclic loads, the mechanical property differences resulted in the MPBs severe strain concentration and plastic deformation. By finite element simulations, the fatigue crack propagation behavior of the SLM samples can be explained. Finally, the crack aspect ratios (a/b) were measured from fracture surfaces. The building directions had no obvious impact on the ratio of a/b whose constant values (a \u003e 300 μm) were about 0.45-0.60.
High Cycle Fatigue Performance of AlSi10mg Alloy Produced by Selective Laser Melting

Z. W. Xu,Q. Wang,X. S. Wang,C. H. Tan,M. H. Guo,P. B. Gao

DOI: https://doi.org/10.1016/j.mechmat.2020.103499

IF: 4.137

2020-01-01

Mechanics of Materials

Abstract:Selective laser melting (SLM), which is an additive manufacturing (AM) technology, has been widely used in industrial fields. The inherent defects resulting from the SLM process are inevitable. The effect of building directions on the static mechanical properties has been observed. However, certain critical functional components are under cyclic loads and extreme service conditions. The effect of inherent defects and building directions on the high cycle fatigue (HCF) performance of SLM alloys is not very clear. More testing data should be provided. Therefore, in the present work, the rotation bending fatigue (RBF) tests of SLM AlSi10Mg bar samples that included three building directions are carried out. These results indicate that most fatigue cracks initiated from the unmelted defects of the sample surfaces (or subsurface). The SLM building directions have an obvious impact on the AlSi10Mg alloy fatigue properties. The 0° samples exhibit a higher fatigue limit value than the 45° and 90° samples. Moreover, the crack propagation mechanism is revealed by fracture analysis. The negative effect of multiple-crack initiation on the RBF specimen fatigue lives under low cyclic loads is explained in detail. Finally, the evaluation method for the fracture toughness (KIC) by the fracture surfaces of the RBF samples is provided.
Influence of Manufacturing Geometric Defects on the Mechanical Properties of AlSi10Mg Alloy Fabricated by Selective Laser Melting

Panding Wang,Hongshuai Lei,Xiaolei Zhu,Haosen Chen,Daining Fang

DOI: https://doi.org/10.1016/j.jallcom.2019.03.135

IF: 6.2

2019-01-01

Journal of Alloys and Compounds

Abstract:The tensile behavior of bulk AlSi10Mg components, fabricated by selective laser melting (SLM), was investigated by uniaxial tensile testing and image-based finite element simulation. The initial morphological features of the structures were imaged by micro X-ray tomography. Moreover, the reconstructed model and as-designed model were compared to quantify the process-induced defects, which remained unavoidable due to complex manufacturing processes. The un-melted AlSi10Mg powders, sticking to the melting pool after condensation, intensified the deviation of side edges. Futhermore, the unevenly distributed process-induced defects resulted in anisotropic mechanical properties of AlSi10Mg alloy. Two finite element models were developed from X-ray tomography images and CAD model, which were simulated by finite element solver ABAQUS/Standard to discuss the effect of initial morphological features on the mechanical behavior of these samples. The geometric defects have slightly reduced Young's modulus and yield strength, but remarkably increased the equivalent plastic strain of the bulk structures. Furthermore, the ultimate strength and elongation, predicted by the image-based finite element model and the ductile failure criterion, was much lower than the values predicted by the as-designed model due to the influence of geometric defects.
Fracture resistance of AlSi10Mg fabricated by laser powder bed fusion

Moses J. Paul,Qian Liu,James P. Best,Xiaopeng Li,Jamie J. Kruzic,Upadrasta Ramamurty,Bernd Gludovatz

DOI: https://doi.org/10.1016/j.actamat.2021.116869

IF: 9.4

2021-06-01

Acta Materialia

Abstract:The combination of refined microstructures (induced by rapid cooling) and melt pool-induced mesostructures in AlSi10Mg fabricated using laser powder bed fusion (LPBF) – a widely used additive manufacturing technique – impart high strength and fracture toughness. Further exploitation of such property combinations requires a detailed understanding of how the processing conditions control the micro- and mesostructures and, in turn, the mechanical performance, especially regarding fracture resistance. Towards this end, the crack resistance curve (R-curve) behavior in different orientations of LPBF-fabricated AlSi10Mg alloys processed with different layer thickness, hatch spacing, and scan strategies was evaluated and correlated with micro- and mesostructural features such as grain size and grain orientation, texture, cell morphology, and melt pool arrangement. Results show a strong anisotropy in both tensile stress-strain behavior and fracture toughness with layer thickness and hatch spacing controlling strength and scan strategy dictating fracture resistance. In terms of tensile stress-strain behavior, the arrangement of melt pool boundaries with respect to loading direction results in anisotropy in ductility whereas strength is controlled by grain size and cellular structure. In case of fracture toughness, measurements show that failure is dominated primarily by melt pool morphology and hence the mesostructure that is controlled by scan strategy. They furthermore reveal, that, despite the pronounced anisotropy in the R-curve behavior the presence of such mesostructure enables a level of damage-tolerance in AlSi10Mg that cannot be achieved in a cast alloy.

materials science, multidisciplinary,metallurgy & metallurgical engineering
Microstructures and tensile properties of a selective laser melted Al–Zn–Mg–Cu (Al7075) alloy by Si and Zr microalloying

Lanbo Li,Ruidi Li,Tiechui Yuan,Chao Chen,Zhijian Zhang,Xiaofeng Li

DOI: https://doi.org/10.1016/j.msea.2020.139492

2020-06-01

Abstract:The application of conventional Al–Zn–Mg–Cu alloys for selective laser melting (SLM) of additive manufacturing is hindered by hot cracking during the SLM process. In the present work, a novel Si- and Zr-modified Al–Zn–Mg–Cu prealloyed powder was developed for SLM, and the printability, microstructure, and mechanical properties of the as-built samples were evaluated at various laser powers. The as-built samples are completely crack-free at various laser powers, showing that Si and Zr effectively prevent hot cracking for SLM printed Al–Zn–Mg–Cu. The mechanisms of tensile property enhancement are as follows: first, the low melting point Si-rich eutectics backfill the cracks; second, the Al3Zr significantly decreases the grain sizes. The microstructure has a bipolar grain distribution with fine grains at the bottom of the melt pool (2–5 μm) and coarse columnar grains (10–30 μm) at the top of the melt pool. The synergistic effect of the Si and Zr contribute to outstanding tensile properties (446 MPa tensile strength and 6.5 % elongation), which are higher than those for SLM printed Al–Zn–Mg–Cu alloys without the addition of Si and Zr.
Deformation effect of melt pool boundaries on the mechanical property anisotropy in the SLM AlSi10Mg

Zihao Jiang,Pingwei Xu,Yilong Liang,Yu Liang

DOI: https://doi.org/10.1016/j.mtcomm.2023.106879

IF: 3.8

2023-08-15

Materials Today Communications

Abstract:The effect of microstructure characteristic on the anisotropy of mechanical properties has been studied for a selective laser melt (SLM) AlSi10Mg material. The cell structure and fine grains at the melt pool boundaries (MPBs) are gradually eliminated by different heat treatment processes. Althought the cell structure of MPB has been eliminated, it is found that the mechanical properties of the transverse specimen and longitudinal specimen are still different due to the heterogeneity of grain. In the process of plastic deformation, when the tensile direction perpendicular to the MPB, the deformation incompatibility between fine grains and columnar grains lead to the excessive stress concentration and rapid fracture along the zone boundary. The change of loading direction can alleviate strain localization and improve the uniform deformation ability of the sample. The heterostructure of SLM AlSi10Mg is related to the remelting and resolidification of MPBs. The results provide guidance for the design of SLM AlSi10Mg material with better mechanical properties.

materials science, multidisciplinary
Effect of microstructural evolution on mechanical properties and fracture modes of AlSi10Mg blocks fabricated by selective laser melting after stress relief annealing

Jianzhu Li,Yujie Li,Zhe Wang,Changguang Li,Hai Yuan,Yun Hao

DOI: https://doi.org/10.1002/adem.202200585

IF: 3.6

2022-09-02

Advanced Engineering Materials

Abstract:AlSi10Mg parts fabricated by selective laser melting (SLM) are frequently reported to have heterogeneous microstructures. How this affects the mechanical properties of SLM parts still requires further study. In this work, AlSi10Mg blocks with simple cuboid shape were printed and annealed at 300 °C. Their microstructure changes significantly from edge to center and from top to bottom. Low temperature annealing is not sufficient to eliminate structural heterogeneity. Before annealing, the Si‐rich phase is fine and mainly exists in the form of a eutectic network. The as‐printed blocks had high tensile strength, and the fracture surface exhibits a mix of transcellular pits and pores. After annealing, the network structure was completely broken or disappeared in most locations in the blocks. The Si‐rich phase is significantly coarsened and even segregated locally along the melt pool boundaries. Yield strength was reduced by 25‐47%, but elongation values were doubled. Tensile samples were fractured by an along‐the‐pool boundary fracture mode along the boundary. Micropores formed during the printing process were aggregated in the about 200 μm thick outer surface layer of the block. They also have a significant effect on the local elongation both before and after annealing. This article is protected by copyright. All rights reserved.

materials science, multidisciplinary
Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Ziyu Zhai,Wei Pan,Bo Liang,Yantao Liu,Yongzhong Zhang

DOI: https://doi.org/10.3390/cryst12040565

IF: 2.7

2022-04-18

Crystals

Abstract:In this paper, the cracking of Al-Mn-Mg-Sc-Zr alloys prepared by selective laser melting (SLM) was comprehensively explored and the influence of process parameters on the generation and propagation of cracks was deeply studied. It was found that the higher laser power and volume energy density will lead to a decrease in the relative density of the material. The lower laser power or volume energy density will lead to cracking of the alloy. The microstructure analysis indicated that plenty of manganese-rich second phases precipitated at the bottom of the melt pool, which increased the tendency of cracking occurred at the bottom of the melt pool. Through the optimization of the process parameters, the SLM forming process parameters of the Al-5.22Mn-1.16Mg-0.81Sc-0.46Zr alloy are successfully obtained, and the crack-free tensile samples are prepared. The microstructure and mechanical properties of the as-deposited aluminum-manganese alloy is analyzed. The bottom and inside of the melt pool are equiaxed grains. The size of the equiaxial grains at the bottom of the melt pool is less than 2 μm, and the coarse equiaxial grains inside the melt pool are approximately 5 μm. As-deposited alloy has a room temperature tensile strength of 455.2 ± 0.7 MPa and elongation of 15.4 ± 0.3%. This study provides guidance for selective laser melting forming of high-strength aluminum-manganese alloy parts, and promotes the industrial production of high-strength aluminum alloy near net forming complex parts.

materials science, multidisciplinary,crystallography
Microstructure, wear and residual stresses of selective laser melting AlSi10Mg solid cylinder

Harinadh Vemanaboina,Ankammarao Padamurthy,Praveen Kumar Gandla,Lakshman Rao Muppa,Koyyagura Lakshmi Kala

DOI: https://doi.org/10.1177/09544089241272825

2024-08-29

Proceedings of the Institution of Mechanical Engineers Part E Journal of Process Mechanical Engineering

Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. Advanced industrial processing technique selective laser melting (SLM) can handle various materials. Although titanium alloys are the main material used in SLM, aluminium alloys may be employed in the future. However, producing aluminium alloys is more complicated. This work uses SLM to make an AlSi10Mg solid cylinder. The aim is to study the mechanical properties and microstructure of products. Layer thickness increases defects; thus, research advises avoiding it. The optical microscope study proved the conduction melting process's stability and hole-freeness. EDX mapping and SEM were used to compare the chemical makeup of as-cast and SLM materials. An unusual microstructure showed consistent alloying component distribution. Investigations examine wear, hardness and residual stresses. Extreme hardness was found. The component has evenly distributed compressive residual stresses within material yield limits.

engineering, mechanical
Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V

Hao Zhang,Tao Gao,Chang Xu,Lingyu Zhao,Haipeng Song,Ganyun Huang

DOI: https://doi.org/10.1007/s12540-023-01433-7

IF: 3.451

2023-04-12

Metals and Materials International

Abstract:The deformation and failure of Ti6Al4V produced by Selective Laser Melting (SLM) under tensile and shear stress states have been experimentally investigated with different types of the samples. The digital image correlation (DIC) method was applied to observe the deformation, crack initiation and propagation behavior. The effects of building direction on the mechanical behavior were studied. The experimental results show that the yield strength and tensile strength of SLM manufactured Ti6Al4V along the build direction is slightly lower than the horizontal one, but the vertical samples have a higher ductility than horizontal samples. Fractographic analyses were conducted to investigate the damage mechanism and fracture mode of Ti6Al4V under different loading conditions. The defects and stress states have a significant influence on damage and failure behaviors of addictively manufactured Ti6Al4V alloy. The tensile stress tends to open up the defects in the vertically built specimen while the defects tend to be closed in the horizontally built specimen due to the building orientation. The nucleation, growth and coalescence of micro voids are the main damage mechanism of SLM fabricated Ti6Al4V alloy under tensile loading condition, and the void shearing mechanism dominates the failure of shear samples. Graphical

materials science, multidisciplinary,metallurgy & metallurgical engineering

Antibodies to blood coagulation factors.

In-situ dwell-fatigue fracture experiment and CPFE simulation of SLM AlSi10Mg alloy at high temperature

In-situ Investigation of the Anisotropic Mechanical Properties of Laser Direct Metal Deposition Ti6Al4V Alloy

Microstructure and Mechanical Properties of Selective Laser Melted Mg-9 Wt%al Powder Mixture

Fatigue and Fracture Behavior of AlSi10Mg Manufactured by Selective Laser Melting: A Review

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Effect of the Boundary Orientation of Melt Pool on Mechanical Property and Fracture Path in Selective-Laser-Melted AlSi10Mg Alloy

Effect of Processing Parameters on Tensile Properties and Microstructure of Selective Laser Melted AlSi10Mg Alloy

In-situ SEM Investigation on Fatigue Behaviors of Additive Manufactured Al-Si10-Mg Alloy at Elevated Temperature

Selective laser melting of Al-3.48Cu-2.03Si-0.48Sc-0.28Zr alloy: Microstructure evolution, properties and metallurgical defects

Microstructure, metallurgical defects and hardness of Al–Cu–Mg–Li–Zr alloy additively manufactured by selective laser melting

Fatigue performance and crack propagation behavior of selective laser melted AlSi10Mg in 0°, 15°, 45° and 90° building directions

High Cycle Fatigue Performance of AlSi10mg Alloy Produced by Selective Laser Melting

Influence of Manufacturing Geometric Defects on the Mechanical Properties of AlSi10Mg Alloy Fabricated by Selective Laser Melting

Fracture resistance of AlSi10Mg fabricated by laser powder bed fusion

Microstructures and tensile properties of a selective laser melted Al–Zn–Mg–Cu (Al7075) alloy by Si and Zr microalloying

Deformation effect of melt pool boundaries on the mechanical property anisotropy in the SLM AlSi10Mg

Effect of microstructural evolution on mechanical properties and fracture modes of AlSi10Mg blocks fabricated by selective laser melting after stress relief annealing

Cracking Behavior, Microstructure and Properties of Selective Laser Melted Al-Mn-Mg-Sc-Zr Alloy

Microstructure, wear and residual stresses of selective laser melting AlSi10Mg solid cylinder

Study on the Tensile and Shear Behaviors of Selective Laser Melting Manufactured Ti6Al4V