Abstract:Laser powder bed fusion (LPBF) allows the fabrication of complex parts with high resolution. In the process of manufacturing complex parts, overhanging structures with unique mechanical properties are inevitable. The mechanical properties are relevant to the microstructure that are severely influenced by the support structures and build orientation. In this study, a three-dimensional finite element model was established to numerically investigate the thermal behavior of the melt pool in the overhanging structures, and the effects of different forming conditions on tensile behavior were analyzed through the microstructure of overhanging specimens and fracture surfaces of failed specimens. The simulation results show that the change trend of the melt pool size is the same as that of the maximum temperature. Moreover, the melt pools closer to the down-facing surface of overhanging structures carry higher temperature and larger size. The application of the support structures effectively reduces the temperature of the melt pool in the starting layer by 5.3%. With the increase of inclination angle, the melt pool temperature in the starting layer decreases slightly. The experimental results indicate that the mechanical properties of 45° specimens fabricated above the entity are stronger than those of 45° specimens with support structures, and the mechanical properties of 45° specimens with support structures are stronger than those of 45° specimens without support structures. Moreover, the mechanical properties of the specimens deteriorate when the build orientation of the overhanging structures varies from 0° to 45°. The mechanical properties of different specimens with 45° build orientation are mainly affected by the thickness of defect area, and the mechanical properties of the specimens with different build orientations are mainly affected by fracture path. The results will facilitate the understanding and application of the LPBF manufacturing technique for overhanging structures in complex parts.

Fatigue performance and crack propagation behavior of selective laser melted AlSi10Mg in 0°, 15°, 45° and 90° building directions

High Cycle Fatigue Performance of AlSi10mg Alloy Produced by Selective Laser Melting

The influence of building direction on the fatigue crack propagation behavior of Ti6Al4V alloy produced by selective laser melting

Effect of the Boundary Orientation of Melt Pool on Mechanical Property and Fracture Path in Selective-Laser-Melted AlSi10Mg Alloy

Very-high-cycle fatigue behavior of AlSi10Mg manufactured by selective laser melting: Effect of build orientation and mean stress

Defect induced fatigue failure behavior and life assessment of laser powder bed fused Al-Si alloy under different building directions

Effect of construction angles on microstructure and mechanical properties of AlSi10Mg alloy fabricated by selective laser melting

In-situ tensile testing of fracture and strain in a selective laser melted AlSi10Mg alloy

Fatigue Performance Differences Between Rolled and Selective Laser Melted Ti6Al4V Alloys

In-situ dwell-fatigue fracture experiment and CPFE simulation of SLM AlSi10Mg alloy at high temperature

Effect of microstructural evolution on mechanical properties and fracture modes of AlSi10Mg blocks fabricated by selective laser melting after stress relief annealing

Effect of building orientations and heat treatments on AlSi10Mg alloy fabricated by selective laser melting: microstructure evolution, mechanical properties, fracture mechanism and corrosion behavior

Fatigue and Fracture Behavior of AlSi10Mg Manufactured by Selective Laser Melting: A Review

In-situ SEM Investigation on Fatigue Behaviors of Additive Manufactured Al-Si10-Mg Alloy at Elevated Temperature

Deformation effect of melt pool boundaries on the mechanical property anisotropy in the SLM AlSi10Mg

Fracture resistance of AlSi10Mg fabricated by laser powder bed fusion

Study on Small Fatigue Crack Growth Rate of SLM AlSi10Mg Alloy

Effects of building direction and defect sensitivity on the fatigue behavior of additively manufactured H13 tool steel

Tensile behavior of AlSi10Mg overhanging structures fabricated by laser powder bed fusion: Effects of support structures and build orientation

The effect of defect population on the anisotropic fatigue resistance of AlSi10Mg alloy fabricated by laser powder bed fusion

Role of defects on the high cycle fatigue behavior of selective laser melted Al–Mg–Sc–Zr alloy