Abstract:Scanning Electron Microscope (SEM) is an important observational device in scientific research. Over the past decades, scientists have been working on the high temperature deformation measurement and characterization of the critical alloy materials and components in hot sections by in situ observations with SEM. The in situ observations have both important theoretical and high engineering significance in understanding the mechanisms of the microstructure damage evolution of the alloys, understanding their high temperature failure mechanisms, extracting mechanical parameters and improving the accuracy of life prediction methods. However, in situ high temperature measurements in a SEM environment pose major challenges in high efficiency heat source design, establishment of stable high contrast microscopic images, and quantitative measurement of the deformation fields in high temperature environment. New methods and approaches must be therefore developed for measurement of mechanical properties in such harsh environment. In the study presented here, the major difficulties and challenges associated with high temperature experiments implemented in situ SEM are introduced firstly, especially the imaging failure at high temperature. The developments of high temperature in situ SEM technology in recent years are then reviewed, including high temperature in situ test instruments, high temperature imaging technology, and high temperature deformation measurement methods. On this basis, some new research results achieved by our group in the field of creep, fatigue and fracture of nickel based alloy materials at high temperature are introduced, such as the fatigue small and long crack growth behaviors at different temperature as well as in different crystallographic orientations. Nickel based alloy is the critical material for gas turbine and aero-engine due to their excellent creep, fatigue and corrosion resistance at high temperature. Finally, some conclusions of current development in this research field are presented, meanwhile works that need to be further extended in the future are also pointed out.

In-situ SEM Investigation on Fatigue Behaviors of Additive Manufactured Al-Si10-Mg Alloy at Elevated Temperature

In-situ dwell-fatigue fracture experiment and CPFE simulation of SLM AlSi10Mg alloy at high temperature

In-situ Study of Microstructure and Mechanical Properties of GH3536 Alloy Manufactured by Selective Laser Melting at 750 °C

Hot dwell-fatigue behaviour of additively manufactured AlSi10Mg alloy: Relaxation, cyclic softening and fracture mechanisms

In-situ tensile testing of fracture and strain in a selective laser melted AlSi10Mg alloy

In-Situ Tensile Deformation Behavior Of As-Built Laser Direct Metal Deposited Ti-6al-4v Alloy At 200 Degrees C

In Situ Scanning Electron Microscopy Analysis of Effect of Temperature on Small Fatigue Crack Growth Behavior of Nickel-Based Single-Crystal Superalloy

Fatigue and Fracture Behavior of AlSi10Mg Manufactured by Selective Laser Melting: A Review

Deformation Mechanisms of Selective Laser Melted 316l Austenitic Stainless Steel in High Temperature Low Cycle Fatigue

In-situ High-Temperature Mechanical Property Measurement Technology and Its Application in Scanning Electron Microscope

High Cycle Fatigue Performance of AlSi10mg Alloy Produced by Selective Laser Melting

Microstructural and texture evolution investigation of laser melting deposited TA15 alloy at 500?C using in-situ EBSD tensile test

Study on Small Fatigue Crack Growth Rate of SLM AlSi10Mg Alloy

The Low-Cycle Fatigue Behavior, Failure Mechanism and Prediction of SLM Ti-6Al-4V Alloy with Different Heat Treatment Methods

In-situ Comparison of Deformation Behavior at 23 ℃ and 650 ℃ of Laser Direct Melting Deposited Ti-6Al-4V Alloy

Fatigue performance and crack propagation behavior of selective laser melted AlSi10Mg in 0°, 15°, 45° and 90° building directions

In situ SEM fatigue testing technology for metallic materials: a review

A Novel Two-Stage Heat Treatment with Medium-Temperature Aging Influence on Microstructure, Al3(Sc, Zr) Nanoprecipitation, and Application Properties, Enhancing Selective Laser Melting of Al–Mg–Sc–Zr Alloy

High-Temperature Mechanical Properties of Stress-Relieved AlSi10Mg Produced via Laser Powder Bed Fusion Additive Manufacturing

Experimental Study on Stress Concentration of Nickel-Base Superalloy at Elevated Temperatures with an in Situ SEM System

In Situ Scanning Electron Microscopy-Based High-Temperature Deformation Measurement of Nickel-Based Single Crystal Superalloy Up to 800°C