Abstract:In this study, Al-Zn-Mg-Cu alloys components were fabricated by cold metal transfer (CMT) wire arc additive manufacturing (WAAM), and the stress corrosion cracking (SCC) behavior of the alloys with different post-treatments was studied by combining in-situ electrochemical impedance spectroscopy (EIS) with slow strain rate tensile. The hot-rolling process was employed to close the internal pores of the WAAM products, following by single-stage aging (T6) to further improve the mechanical properties of the products. The elongation loss and SCC susceptibility index of T6 sample are 38.0 % and 43.0 %, respectively, which exceed those of the hot-rolled sample at 35.5 % and 37.0 %. Furthermore, the corrosion fracture of the T6 sample exhibits intensive secondary cracks, indicating an increased SCC susceptibility. The stress corrosion process is classified into four stages based on the trend of the EIS: (I) Initial stage of corrosion; (II) Corrosion products accumulation stage; (III) Corrosion products coverage stage; (IV) Approaching fracture stage. The hot-rolled samples have reduced SCC susceptibility due to the presence of coarse grain boundary precipitates (GBPs) which can act as the irreversible traps to capture hydrogen. The ultimate tensile strength and elongation of T6 sample reached 568.3 ± 11.5 MPa and 9.1 ± 0.7 %, respectively. However, the small-sized GBPs and wider precipitates-free zone reduced its SCC resistance. This study found that the hot-rolling process can fully exploit the mechanical property potential of Al-Zn-Mg-Cu alloys and improve their SCC resistance, which is an important guiding significance for the practical application of WAAM technology in Al-Zn-Mg-Cu alloys.

Effect of Different Post-heat Processes on Mechanical Properties and Corrosion Behavior of Al-Cu-Mg-Ag Fabricated by Wire Arc Additive Manufacturing

Effects of solution temperature on microstructure and mechanical properties of Al-Si-Mg aluminum alloy fabricated by wire-arc additive manufacturing

Microstructure evolution and mechanical properties of wire-arc-additively manufactured Al–Cu–Mg–Ag alloy

Influence of heat treatment on the microstructure and mechanical properties of Al–Mg–Si alloy fabricated by double wires + arc additive manufacturing

Effect of solution treatment on porosity, tensile properties and fatigue resistance of Al–Cu alloy fabricated by wire arc additive manufacturing

Microstructure and properties research of Al-Zn-Mg-Cu alloy with high strength and high elongation fabricated by wire arc additive manufacturing

Mechanical properties and precipitation behavior of the heat-treated wire + arc additively manufactured 2219 aluminum alloy

The Effect of Cu Content on the Microstructure and Properties of the Wire Arc Additive Manufacturing Al-Cu Alloy

Microstructure and Mechanical Properties of Cu-6.5%Al Alloy Deposited by Wire Arc Additive Manufacturing

Microstructure and Mechanical Properties of Al-Cu-Mg Alloy Fabricated by Double-Wire CMT Arc Additive Manufacturing

Stress corrosion behavior and microstructure analysis of Al-Zn-Mg-Cu alloys fabricated by CMT wire arc additive manufacturing with different post-treatments

Effect of heat treatment on the microstructure and properties of CuCrZr alloy manufactured by wire arc additive manufacturing

Effects of Deposition Paramaters on the Microstructure Evolution of Wire Arc Additive Manufactured Al–Zn–Mg–Cu Alloy

Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: The comparison of as-deposited and T6 heat-treated samples

Microstructure evolution and mechanical properties of the wire + arc additive manufacturing Al-Cu alloy

Microstructure and Properties of Al-6.0Mg-0.3Sc Alloy Deposited by Double-Wire Arc Additive Manufacturing

Effect of Solution Heat Treatment on Microstructure and some Properties of Al–Cu–Mg Alloy

Microstructure and Mechanical Properties of AlSi7Mg0.6 Aluminum Alloy Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

Effect of Heat Treatment on the Microstructure and Mechanical Properties of AZ91D Magnesium Alloy Fabricated Via GTA Wire Arc Additive Manufacturing

Effect of Post Heat Treatment on the Microstructure and Mechanical Properties of Wire-Arc Additively Manufactured A357 Alloy Components

Microstructural and mechanical properties of wire-arc additively manufactured Al–Zn–Mg aluminum alloy: The comparison of as-deposited and heat-treated samples