Abstract:The aim of this work is to investigate the effect of heat treatment (T6) on the microstructure, mechanical, and corrosion properties of Al 319.0 alloy. In particular, Al 319.0 alloy is developed by squeeze casting using 200 MPa pressure, and further the ingots are solutionized, quenched and artificially aged to develop a homogenous microstructure, improve distribution of secondary phase(s), and mechanical properties at ambient and elevated temperatures. The phase and microstructure of the as-cast and heat-treated Al 319.0 alloys analyzed using X-ray diffraction, optical microscope, and field emission scanning electron microscope illustrate cast ingot contain α -Al as a primary phase and Al 2 Cu, eutectic Si, and Al 5 Si 7 Cu-containing intermetallic as secondary phase(s). However, heat treatment leads to complete dissolution of Al 5 Si 7 Cu and partial dissolution and re-precipitation of Al 2 Cu phase. Moreover, heat treatment changes the morphology of eutectic Si into spheroidal Si, blocky Al 2 Cu into spheroids Al 2 Cu, and the heat-resistant α (FeMn), Al 8 Cu 3 Mn(Si) phases emerged. The tensile test at room and elevated temperatures exhibit significant improvement in the YS and UTS at ambient temperature in heat-treated alloy owing to the presence of precipitation-hardened phases. Importantly, these phases are found stable up to 150 °C and tend to coarsen at 250 °C owing to thermal softening invariably leading to a substantial reduction in mechanical properties. Potentiodynamic polarization and electrochemical impedance spectroscopy shed light on galvanic corrosion phenomena predominant in 0.1 M NaCl solution. In particular, heat-treated alloy specimens demonstrated the lowest corrosion current ( I corr —~1.72 μA/cm 2 ) , and highest polarization resistance ( R p —12260 Ω.cm 2 ) implying superior corrosion resistance as compared to as-cast alloy owing to protective barrier provided by finer Al 2 Cu precipitates and spheroidal Si.

Effect of Solution Heat Treatment on Microstructure and some Properties of Al–Cu–Mg Alloy

Microstructure evolution and mechanical behavior of Cu-7Ni-7Al-4Fe-2Mn alloy via a quenching-aging heat treatment

Effect of Heat Treatment on the Microstructures and Mechanical Properties of Al–4Cu–1.5Mg Alloy

Effect of solution heat treatment on the internal architecture and compressive strength of an AlMg4.7Si8 alloy

The Microstructure, and Mechanical and Corrosion Properties of As-Cast and As-Extruded Mg-2%Zn-x%Cu Alloys After Solution and Aging Heat Treatments

Effect of Solution Temperature and Quench Delay on the Microstructure and Mechanical Properties of an Extruded Al-Mg-Si-Cu-Mn alloy

Effect of heat treatment on the microstructure and mechanical properties of Al‐9Si‐0.4Mg‐0.1Cu alloy

Mechanical Properties, Thermal Properties and Microstructure of Heat-Treated Al-Zn-Mg-x%Cu (0.02 wt% Cu and 0.89 wt% Cu) Alloy

Effect of Heat Treatment on Microstructure, Mechanical, and Corrosion Properties of Squeeze Cast Al 319.0 Alloy

Effect of heat treatment on microstructure and mechanical properties of Cu–6.9Ni–2.97Al–0.99Fe–1.06Mn alloy

Effect of heat treatments on microstructure and mechanical properties of sand cast Al–2Li–2Cu–0.5Mg–0.2Sc–0.2Zr alloy

Study on microstructure and properties of Mg-Al-Si-Ca alloy by heat treatment

Effect of heat treatment on corrosion and ultrasonic cavitation erosion resistance of AlSi10MnMg alloy

Influence of the Solution and Artificial Aging Treatments on the Microstructure and Mechanical Properties of Die-Cast Al–Si–Mg Alloys

Effect of Solution and Aging Treatment on Microstructure and Mechanical Properties of Al–14Si–5Cu–1.1Mg–2.3Ni–0.3La Alloy

Precipitated phase characteristics and fracture behaviour of cast Al–Cu–Mn alloy

Effects of Solution Treatment on Microstructure Transformation, Tensile and Exfoliation Corrosion Properties of 7136 Aluminum Alloy

Microstructure and mechanical properties of squeeze-cast Al−5.0Mg−3.0Zn−1.0Cu alloys in solution-treated and aged conditions

Microstructure and Mechanical Properties of Cast Al-Si-Cu-Mg-Ni-Cr Alloys: Effects of Time and Temperature on Two-Stage Solution Treatment and Ageing

The effect of quenching rates on microstructure and mechanical properties of an Al-Si-Cu-Mg alloy

Effect of solid solution heat treatment following age hardening on microstructure and mechanical properties of 7000 series power aluminum alloy