Abstract:Titanium aluminide (TiAl) alloys are promising high-temperature structural materials in the aerospace field. Additive manufacturing is a desirable process for fabricating TiAl alloys. In the process of wire arc additive manufacturing of TiAl alloys, Al-based and Ti-based wires were used as the feedstocks. However, it is hard to ensure the two different wires melt synchronously under the heat of one single arc, so the desired microstructures with gamma (TiAl) phase and alpha(2) (Ti3Al) phase are hard to obtain. A two-wire TOP-TIG-based additive manufacturing process for TiAl alloys is proposed in this paper. The Ti6Al4V wire and pure Al wire are used as the feedstocks. The Al wire is fed in TOP-TIG mode behind the molten pool, while the Ti6Al4V wire is fed in conventional TIG mode in front of the molten pool. The two wires melt synchronously in a broad range of parameters. The compositions of the component can be controlled by adjusting the two-wire feeding speeds. The main microstructures of the as-fabricated component contain alpha(2)/gamma lamellae colonies, equiaxed gamma grains, and alpha(2) grains. In the top and middle regions, when the Al content is 45 at.%, the structures are full alpha(2)/gamma lamellae; as the Al content increases to 50 at.%, some equiaxed gamma grains distribute at the grain boundaries; the component with 55 at.% Al content exhibits the structures consists of equiaxed gamma grains with snowflake-shaped alpha(2)/gamma lamellae colonies. In the bottom region, all components exhibit the coarse equiaxed alpha(2) grains with gamma laths. As the Al content increases, the alpha(2) phase decreases, but the gamma phase increases, and from the top region to the bottom region, the volume fraction of the alpha(2) increases by about 19.4 %. The hardness value of the top and bottom regions is higher, and the middle region exhibits the lowest hardness. As the Al content increases, the hardness decreases. The component with 50 at.% Al exhibits the highest compressive strength with 1762 MPa and the largest compressive ratio with 26.1%.

Microstructure and mechanical properties of Al-Cu alloy during wire and arc additive manufacturing by adding micron TiB2 particles

Promoting Strengthening and Grain Refinement of Aluminum Alloy During Wire and Arc Additive Manufacturing by Adding TiB2 Particles

Realization of synergistic enhancement for fracture strength and ductility by adding TiC particles in wire and arc additive manufacturing 2219 aluminium alloy

Contribution Made by Double-Sized TiC Particles Addition to the Ductility–strength Synergy in Wire and Arc Additively Manufactured Al–Cu Alloys

Effect of Alloying Powders on Microstructure and Mechanical Properties of Aluminum Alloy Arc Additive Manufacturing

Realization of structural evolution in grain boundary, solute redistribution and improved mechanical properties by adding TiC<sub>nps</sub> in wire and arc additive manufacturing 2219 aluminium alloy

Effect of Cu content on microstructure and properties of Ti-6Al-4V alloy fabricated by double-wire arc additive manufacturing

Evolution of crystallographic orientation, columnar to equiaxed transformation and mechanical properties realized by adding TiC<sub>ps</sub> in wire and arc additive manufacturing 2219 aluminum alloy

Al–Zn–Mg–Cu alloy with both high strength and high plasticity fabricated with wire arc additive manufacturing

Improvement of microstructure and mechanical properties of CMT wire arc additive manufacturing Al-Si alloy deposition via interlayer coating TiC nanoparticles

Microstructure and mechanical properties of Ti-3Al-2V alloy by dual wire + arc additive manufacturing

Microstructure and properties of Al–7Si–0.6Mg alloys with different Ti contents deposited by wire arc additive manufacturing

Research on Technology of 7075 Aluminum Alloy Processed by Variable Polarity TIG Additive Manufacturing Utilizing Nanoparticle-Reinforced Welding Wire with TiB2

Microstructure and Mechanical Properties of TiB2/AlSi7Mg0.6 Composites Fabricated by Wire and Arc Additive Manufacturing Based on Cold Metal Transfer (WAAM-CMT)

Microstructure and Mechanical Properties of TiB2/ Al-Si Composites Fabricated by TIG Wire and Arc Additive Manufacturing

Microstructure and mechanical properties of wire arc additively manufactured 205A high strength aluminum alloy: The comparison of as-deposited and T6 heat-treated samples

Effects of V Element and Heat Treatment Process on Microstructure and Mechanical Properties of Additive Manufacturing of Titanium Aluminum Alloy Using Flux-Core Arc Welding Wire with TiH2 Powder

Wire Arc Additive Manufacturing of Titanium Aluminide Alloys Using Two-Wire TOP-TIG Welding: Processing, Microstructures, and Mechanical Properties

Effect of Heat Treatment Processes on the Microstructure and Mechanical Properties of High-Strength Aluminum Alloy Deposited Layers Processed by Fused Arc Additive Manufacturing

Effect of TiB2 addition on microstructure and fluidity of cast TiAl alloy

Microstructure and Mechanical Properties of Cu-6.5%Al Alloy Deposited by Wire Arc Additive Manufacturing