Abstract:The Frequency Division Multiplexing (FDM) has been used in wireless communication to transmit large amounts of data. FDM separates and transmits multiple information streams through a single communication channel simultaneously. The capacity to store information increases with higher frequencies. However, the problem of maintaining stability arises with high frequencies. To address this, a frequency multiplier (FM) is employed to convert a low-frequency source, which is easier to stabilize, into a high frequency. To ensure the proper functioning of FM, it is crucial to achieve symmetrical matching between two adjacent waveforms of two cycles of output from one cycle of input. This paper introduces three techniques for FM operation. Firstly, the implementation of tunnel FET (TFET) is proposed to solve the issue of harmonics, which commonly occurs in existing FMs. TFET possesses ambipolar properties, making it suitable for solve harmonic issue. Secondly, high-k (HK) dielectric materials are utilized to enhance on-current and ambipolar current. Lastly, hetero gate dielectrics (HG) are employed to increase the ambipolar current, ensuring its equivalence to the on-current. This contrasts with existing TFETs that use HG to reduce ambipolar current. We can control on-current and ambipolar current, respectively, by adjusting HK length at the source-side and HK at the drain-side using the HG structure. In addition, achieving matching currents is essential for obtaining symmetrical adjacent output waveforms, which is the primary objective of FM. From the proposed structure, we confirmed that frequency doubling is possible by symmetrically matching on-current and ambipolar current for FM to operate normally.

A Frequency Doubler With Second Harmonic Feedback for Wideband, Efficient Frequency Multiplication at Millimeter-Wave

A Wideband CMOS Frequency Quadrupler with Transformer-Based Tail Feedback Loop.

Ultralow Power K-Band Frequency Doubler with Differential Output

An Ultra-Low Power K band Balanced Frequency Doubler with a Novel Current-reused Structure

A Dual-Mode Mm-Wave Injection-Locked Frequency Divider with Greater Than 18% Locking Range in 65nm CMOS

A 90-98-ghz FMCW Radar Transceiver Supporting Broadband Modulation in 65nm CMOS

A 276–312-Ghz (×12) Frequency Multiplier Chain with Milliwatt Level Output Power in 65-Nm CMOS Technology

An 8.3% Efficiency 96–134 GHz CMOS Frequency Doubler Using Distributed Amplifier and Nonlinear Transmission Line

A 26-38GHz Ultra-Wideband Balanced Frequency Doubler in 0.15µ m GaAs pHEMT Process

A Frequency Doubling Two-Path Phased-Array FMCW Radar Transceiver in 65nm CMOS

A Novel Architecture for Frequency Doubler Featuring Compact 3-D Stacked Packaging and Four Multiplying Structures

A Balanced Frequency Doubler Covering 140-220 GHz With an Efficiency of 6.8%-11.6%

A 170–230 GHz High-Power Frequency Doubler Based on a GaAs MMIC Process

A 39 GHz–80 GHz Millimeter-Wave Frequency Doubler with Low Power Consumption in 65nm CMOS Tehnology

A 220 GHz High-Efficiency Doubler Based on Function-Based Harmonic Impedance Optimization Method

A W-Band Frequency-Doubling Phase Shifter for Concurrent Signal Doubling and Phase Shifting

A 232GHz Frequency Multiplier Chain(×4) in 65-nm CMOS with Harmonic Rejection Ratio of 40dBc

A 5.1 Dbm 127–162 GHz Frequency Sextupler with Broadband Compensated Transformer-Based Baluns in 22nm FD-SOI CMOS

Frequency Doubler Utilizing Hetero Gate Dielectric Tunnel Field-Effect Transistor

24.3 A 200-to-350ghz SiGe BiCMOS Frequency Doubler with Slotline-Based Mode-Decoupling Harmonic-Tuning Technique Achieving 1.1-to-4.7dbm Output Power

Full Waveguide Matching Design for 220 GHz Frequency Doubler