Abstract:One of the key challenges to realize a fully integrated transceiver using silicon based processes is the limited output power achievable, especially at millimeter-wave frequencies. Higher output power can be obtained by using various power combining schemes, which typically sum the output power of N identical amplifying stages coherently. Thus to ensure efficient power combining, the input signal must be distributed to all the amplifying stages on the chip with equi-phase and equi-magnitude. While Wilkinson power splitter has been employed for this purpose in the literatures, it becomes bulky and inefficient when N is large, which severely limits the number of outputs that can be combined.In this paper, a network of coupled lambda/2 standing-wave oscillators is employed to distribute the input signal. Proposed formerly for global clock distribution, theoretically, differential signals of equi-frequency, equi-phase, and equi-magnitude can be obtained by taping onto specific points in the network. It should be noted, however, that the network is especially suited for input signal distribution purpose here, since the specific power combining scheme assumes that a grid of N amplifying stages resides on the chip, which matches to the tap points in a perfect way.A 30 GHz prototype network comprised of four coupled lambda/2 standing-wave oscillators using TSMC 0.18 mu m CMOS process has been design. Post-layout simulation results are presented showing that no distinguishable difference in frequency, phase, and amplitude is observed for the multiple output differential signals. The chip has a total area (including pads) of 800 x 990 mu m(2) and has been submitted for fabrication.

A 5.1 Dbm 127–162 GHz Frequency Sextupler with Broadband Compensated Transformer-Based Baluns in 22nm FD-SOI CMOS

A Wideband CMOS Frequency Quadrupler with Transformer-Based Tail Feedback Loop.

Compact CMOS Baluns for the 4–10 GHz Band Applications

An Ultra-Low Power K band Balanced Frequency Doubler with a Novel Current-reused Structure

Ultralow Power K-Band Frequency Doubler with Differential Output

An 18 similar to 30 GHz Vector-Sum Phase Shifter With Two-Stage Transformer-Based Hybrid in 130-nm SiGe BiCMOS

An 18~30 GHz Vector-Sum Phase Shifter with Two-Stage Transformer-Based Hybrid in 130-Nm SiGe BiCMOS

Three-solenoid Windings Transformer Baluns on CMOS-grade Silicon Substrate

A High-Precision Ultra-Broadband Quadrature Generation at Millimeter-Wave Frequencies

A Compact 2-18Ghz Ultra-Wideband Frequency-conversion T/R Module Based on a 3D Heterogeneous Integrated Process

A 0.7-8 GHz High IF Frequency-Extended Transmitter Front-End with −47.1-Db EVM at 16 QAM in 65-Nm CMOS

Input Signal Distribution Using Coupled Lambda/2 Standing-Wave Oscillators For Coherent Power Combining

Analysis and Design of Broadband Balance-Compensated Transformer Baluns for Silicon-Based Millimeter-Wave Circuits

A Balanced Frequency Doubler Covering 140-220 GHz With an Efficiency of 6.8%-11.6%

A 26-38GHz Ultra-Wideband Balanced Frequency Doubler in 0.15µ m GaAs pHEMT Process

An 8.3% Efficiency 96–134 GHz CMOS Frequency Doubler Using Distributed Amplifier and Nonlinear Transmission Line

24.3 A 200-to-350ghz SiGe BiCMOS Frequency Doubler with Slotline-Based Mode-Decoupling Harmonic-Tuning Technique Achieving 1.1-to-4.7dbm Output Power

A 91.9-113.2 GHz Compact Frequency Tripler with 44.6 dBc Peak Fundamental Harmonic-Rejection-Ratio Using Embedded Notch-filters and Area-Efficient Matching Network in 65 nm CMOS

A CMOS W-band ×4 frequency multiplier with cascading push-pull frequency doublers

Optimally Matched 189-232 GHz 6.8 dBm Output Power CMOS Frequency Doubler

A 170‐ to 260‐GHz Full‐Band Frequency Doubler Realized by Impedance Compression Matching Technique