Abstract:Silicon carbide (SiC) is an effective material for high-temperature engineering applications owing to its desirable properties such as high elastic modulus, high hardness, and melting temperature, high thermal conductivity, good corrosion and oxidation resistance, low density, and coefficient of thermal expansion compared with other advanced ceramics. Nevertheless, poor sinterability and low toughness limit its use, which can be overcome using appropriate additives. In this study, the effect of different amounts of nano-β-SiC (0, 5, 10, and 15 wt.%) and graphene (0, 1, 2, and 3 wt.%) particles on the sinterability behavior and microstructure of SiC composite has been investigated. After weighing, dispersing nano-β-SiC and graphene, and mixing the starting materials, milling was carried out at 180 rpm for 3 h. The materials obtained were then compressed uniaxially under a pressure of 75 MPa and then were compressed again through CIP under 150 MPa. To remove volatile products, the pyrolysis process was performed at 800 °C under Ar atmosphere. Finally, the samples were sintered at 2200 °C for 2 h by the pressureless sintering process. XRD analysis was used to investigate the phases and FESEM images were used to study the microstructure. According to the XRD patterns, β-SiC particles were converted to α-SiC, which was accompanied by the elongation of SiC grains. Also, no reaction was observed between graphene and the SiC matrix. According to the FESEM images, the samples containing 5 wt.% nano-β-SiC and 1 wt.% graphene showed a uniform distribution of reinforcement particles but with increasing the amount of the reinforcement particles, agglomeration was observed. According to the results, upon increasing the nano-β-SiC up to 5 wt% and graphene up to 1 wt.%, all the measured properties including relative density, and linear shrinkage improved and reached 99.04%, and 18.01%, respectively. However, with increasing the additives, these properties deteriorated due to increasing porosity and agglomeration in the composite structure.

High-Temperature Properties of SiC-Si3N4 Particle Composites

High-temperature tensile behavior of 3D SiC/SiC composites

Pressureless Sintering and High-Temperature Strength of SiC-AlN Ceramics

Mechanical Properties and Interfaces of Cf/SiC Composites

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Effects of SiC contents on the microstructure and mechanical properties of Al4SiC4–SiC ceramic composites

High-Temperature Strength of Sic-Aln Solid-Solutions and Composites As Evaluated by Small Punch Tests

THE RESEARCH SITUATION OF THE THE HIGH-TEMPERATURE RESISTANCE OF Si3N4 BONDED SiC COMPOSITES

Pressureless sintering of SiC matrix composites reinforced with nano-β-SiC and graphene

Densification and Mechanical Properties of Si3N4/SiC Nanocomposite Using Si-Nitrided Si3N4 Powder

Fabrication and Mechanical Properties of Si3N4/SiC Nanocompoisites under Pressureless Sintering.

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Experimental Study of High-Temperature Tensile Mechanical Properties of 3D Needled C/C–SiC Composites

Solid Particle Erosion-Wear Behavior of SiC–Si 3 N 4 Composite Ceramic at Elevated Temperature

Thermophysical and Mechanical Properties of A Three-Dimensional Hi-Nicalon/Sic Composite

Characterization of a Powder Metallurgy SiC/Cu–Al Composite

Mechanical properties and microstructure evolution of 3D C f /SiBCN composites at elevated temperatures

Microstructure, phase compositions and mechanical properties of slip cast sintered SiC/Si3N4 composites

Microstructure and Mechanical Properties of SiC F /sibcn Ceramic Matrix Composites

Fabrication and Properties of Si<sub>3</sub>N<sub>4</sub>-SiC-C Refractory Composites

Fluoride doped SiC/Si3N4 composite as a high thermal conductive material with enhanced mechanical properties