Abstract:Al–Nb–B refiner has been considered as an alternative to Al–Ti–B refiner for hypoeutectic Al–Si alloys due to Si-poisoning effect. In this paper, the effects of Al–Nb–B and Al–Ti–B refiner on the microstructure and mechanical properties in indirect squeeze casting Al–8Si-0.2Mg-0.5Mn alloy were compared. Results show that the grain sizes in the edge chilling layer, segregation band, and the center region of the Al–Nb–B refined alloys were refined by 13.9%, 12.5%, and 17.6% compared to Al–Ti–B refined alloys, respectively. The yield strength, tensile strength, and elongation of Al–Nb–B inoculated alloys were superior to those of the unrefined alloys and Al–Ti–B inoculated alloys. The coexistence of NbAl 3 and NbB 2 particles in the Al–Nb–B refiner exhibited excellent anti Si-poisoning capability. They significantly decreased the grain size and uniformly distributed the eutectic Si particles and Fe-rich phases, resulting in an increase in the yield strength of the alloy by 16.1% compared to the Al–Ti–B inoculated alloy. The distribution of iron-rich phases in the segregation band was affected by the inoculation. The size of α-Al 15 (Fe, Mn) 3 Si 2 phase in Al–Ti–B inoculated alloys was refined, and the number significantly increased, resulting in a decrease in tensile strength of 12.82 MPa. In the Al–Nb–B inoculated alloys, the size and number of α-Al 15 (Fe, Mn) 3 Si 2 phase decreased, and the δ-Al 4 FeSi 2 phase increased, which effectively improved the fracture toughness and ductility. In addition, with the increase in grain refinement (from unrefined to Al–Ti–B to Al–Nb–B inoculated alloy), the fracture behavior changed from trans -granular fracture to intergranular fracture, improving the fracture toughness.

Investigation of Grain Refinement and Mechanical Properties of Al-7Si Alloy with Al-5Nb-1B Master Alloy Addition Treated by Ultrasound Treatment

Influence of high-intensity ultrasound on grain refining performance of Al–5Ti–1B master alloy on aluminium

Effect of High-intensity Ultrasonic on the Microstructure and Grain Refinement of Al-5Ti-1B Master Alloy

Microstructure Evolution and Mechanical Properties of As-Cast and Ultrasonic Treated Nb-16Si-xCr Alloys

Microstructure Modification and Mechanical Performances Enhancement of Ti44Al6Nb1Cr Alloy by Ultrasound Treatment

Effects of Ultrasonic Stirring on Microstructures of Al 7wt%Si Alloy Ingot

Effects of Niobium and Ultrasonic Action Coupling on Microstructure Evolution and Mechanical Properties of Ti46Al2.6 C Alloy

Development of Al–Nb–B master alloy with high Nb/B ratio for grain refinement of hypoeutectic Al–Si cast alloys

Microstructural Refinement of Al-Si Alloy Upon Ultrasonic Nanocrystalline Surface Modification Treatment

Grain refinement and mechanical properties of Mg–5Li–3Al alloy inoculated by Al–5Ti–1B master alloy

The Control of Nbb2 Particles in Al-Nbb2 Master Alloy and its Effect on Grain Refinement of Az91 Magnesium Alloy

Study on Grain Refinement and Refining Mechanism of Al-Si-Mg Alloy

Improving Primary Nbss Morphology and Fracture Toughness in Hypoeutectic Nb-Si-Ti Ternary Alloy by Ultrasonic Treatment

Grain refinement and eutectic modification of A356 casting alloy by adding Al-B-Sr master alloys and its effect on tensile properties

Microstructure and mechanical properties of non-heat-treated Al-8Si-0.2Mg-0.5Mn alloy inoculated by Al-Nb-B refiner

Effect of ultrasonic melt processing and Al-Ti-B on the microstructural refinement of recycled Al alloys

Effects of Alloying on the Microstructures and Mechanical Property of Nb-Mo-Si Based in Situ Composites

Boosting the grain refinement of commercial Al alloys by compound addition of Sc

Optimization of Processing Parameters for Preparation of Al-3Ti-1B Grain Refiner

Research on Refinement of the High-Strength and Ductility Al-Si Alloy

The Size Distribution of TiB2 Particles and Grain Refining Performance of an Al-5Ti-1B Master Alloy Prepared Under Ultrasonic Vibration