Abstract:Grain refinement of Zr–containing Al alloys has attracted extensive attention for many years in both industry and academia, since "Zr–poisoning" phenomenon always happens when commercial refiner is applied in such alloys. This unrecoverable grain nucleating obstacle finally leads to poor grain refinement efficiency. In this work, a special Al–Ti–C master alloy rich in TiC nano–particles was applied to a high–strength Al–Zn–Mg–Cu–Zr alloy (i.e. 7050 alloy). The effects of TiC nano–particles on the microstructure and mechanical properties of 7050 alloy during solidification, hot extrusion and subsequent heat treatment were systematically investigated. The results show that prominent grain refinement occurs with TiC addition through both the growth restriction effect and heterogeneous nucleation. Meanwhile, TiC nano–particles are more inclined to distribute along grain boundaries than the interior of matrix grains after solidification. After subsequent homogenization and hot extrusion, TiC nano–particles tend to align along extrusion direction. In comparison with 7050 matrix alloy, the tensile properties especially ductility of 1% TiCp/7050 composite after heat treatment have been improved obviously. Furthermore, it is worth noting that precipitates in the composite have also been obviously refined. Synergetic effects of grain refinement, refined precipitates and increased dislocation density are responsible for the optimized mechanical properties of TiCp/7050 composite. This work provides new insights for controlling matrix grains of Zr–containing Al alloys and developing low–cost Al matrix composites.

Grain refinement of A356 alloy by Al–Ti–B–C master alloy and its effect on mechanical properties

Grain refinement and eutectic modification of A356 casting alloy by adding Al-B-Sr master alloys and its effect on tensile properties

A Novel Al-Ti-C-B-Ce Alloy Preparation Process and Its Refinement Effect to A356 Alloy

Effect of Al-3 wt% Al2O3 master alloy fabricated by calcined kaolin on grain refinement and mechanical properties of A356 alloy

The Grain Refinement Mechanism of AlTiC, Al4B and Al3Ti4B Master Alloy in Pure Aluminium and Hypoeutectic Al-Si Alloys

Influences of Preparation Conditions and Melt Treatment Procedures on Melt Treatment Performance of Al-5Ti-B and Al-10Sr Master Alloys

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Recent Development in Research of AlTiC Master Alloy

Microstructure evolution and enhanced mechanical properties in Al-Mn alloy reinforced by B-doped TiC particles

Performance Comparison of AlTiC and AlTiB Master Alloys in Grain Refinement of Commercial and High Purity Aluminum

Effect of Mg–TiB2 master alloy on the grain refinement of AZ91D magnesium alloy

STUDY ON THE MICROSTRUCTURES AND GRAIN REFINING PERFORMANCE OF Al-Ti-C GRAIN REFINING MASTER ALLOYS

The grain refinement of high-purity aluminum by aluminum-transition metal alloys

The Grain Refinement of 1070 Alloy by Different Al-Ti-B Mater Alloys and Its Influence on the Electrical Conductivity

Effect of Ti content on microstructures and mechanical properties of cast Al-2Li-2Cu-0.5Mg alloy

Strengthening behavior of B doped TiC particles on an Al–Zn–Mg alloy

Enhanced grain refinement and mechanical properties of a high–strength Al–Zn–Mg–Cu–Zr alloy induced by TiC nano–particles

Grain Refinement of Al-5Ti-0.62C-0.2Nd Grain Refiner for Commercial Pure Aluminum and Its Effect on Mechanical Properties

Effect of Grain Refinement on the Microstructure and Tensile Properties of Cast Aluminum A356.2 Alloy Knuckles Made by Counter Pressure Casting (CPC) Process

Hereditary Effect of Al-based Modifiers and Grain Refiners on Structure and Properties of A356.2 Alloys

Grain refining performance of Al–Ti master alloys with different microstructures