Abstract:Al–7.5Si–4Cu cast alloy melt modified by Al–5Ti–B, RE and Al–10Sr master alloys were poured in the chromite sand moulds, to investigate comparatively the effects of individual or combined additions of grain refiners and modifiers on the mechanical properties, microstructures, grain refining and modification, and intermetallic compounds of the alloy. The results show that the mechanical properties and the microstructures of Al–7.5Si–4Cu cast alloys are improved immensely by combining addition of 0.8%Al–5Ti–B, 0.1%RE and 0.1%Al–10Sr grain refiners and modifiers compared with the individual addition and cast conditions. For individual addition condition, addition of 0.8% Al–5Ti–B master alloy can obtain superior tensile strength, Brinell hardness and finer equiaxed α(Al) dendrites. The alloy with 0.1% RE master alloy shows the highest improvement in ductility because the rare earth can purify the molten metal and change the shape of intermetallic compounds. While the alloy with 0.1% Al–10Sr modifier shows only good improvement in yield strength, and the improvement of other performance is unsatisfactory. The Al–10Sr modifier has a significant metamorphism for the eutectic silicon, but will make the gas content in the aluminum alloy melt increase to form serious columnar grain structures. The effects of grain refining and modification on mean area and aspect ratio have the same conclusions obtained in the mechanical properties and the microstructures analyses.

Grain refinement and eutectic modification of A356 casting alloy by adding Al-B-Sr master alloys and its effect on tensile properties

Grain refinement of A356 alloy by Al–Ti–B–C master alloy and its effect on mechanical properties

Near eutectic Al-Si-Mg casting alloy with high mechanical properties and low cost

Effects of Al-Ti-B-RE + Al-10Sr Master Alloys on Refinement and Modification Performances of A356 Alloy

Influence of Boron on the Microstructure and Mechanical Properties of Al-11.6si-0.4mg Casting Alloy Modified with Strontium

Effects of Grain Refining and Modification on Mechanical Properties and Microstructures of Al–7.5Si–4Cu Cast Alloy

Hereditary Effect of Al-based Modifiers and Grain Refiners on Structure and Properties of A356.2 Alloys

Effect of Al-Sr-Y intermediate alloy on microstructure and mechanical properties of A356 alloy

Grain refinement and tensile properties improvement of aluminum foundry alloys by inoculation with Al-B master alloy

Influence of Al-Ti-B Addition on the Microstructure and Mechanical Properties of A356 Alloys

Influence of Combined Melt Treatment of Sr + B on the Microstructure of Al-Si Casting Alloy

Grain refining performance of Al-B master alloys with different microstructures on Al-7Si alloy

Concurrent effects of various B additions on grain refinement, Fe intermetallics morphologies, and ductility evolution of Al-7.5Si-0.55 Mg (A357) cast alloy

The Effect of Sr Modification on the Microstructure and Properties of Mg2si Reinforced Near- Eutectic Al-Si Alloy

Effect of Sc and Sr on the Eutectic Si Morphology and Tensile Properties of Al-Si-Mg Alloy

Effect of Al-5Ti-1B on the microstructure of near-eutectic Al-13.0%Si alloys modified with Sr

Influence of Combined Melt Treatment of Sr + B on Microstructure and Mechanical Properties of Al-Si-Mg Casting Alloy

Influences of Preparation Conditions and Melt Treatment Procedures on Melt Treatment Performance of Al-5Ti-B and Al-10Sr Master Alloys

Grain Refinement Effect of Al-B Master Alloy on Al-Mg-Si Wrought Alloy Made of Electrolytic Low-titanium Aluminium

Grain refinement and mechanical properties of Mg–5Li–3Al alloy inoculated by Al–5Ti–1B master alloy

Grain Refining Efficiency of Al-V-B Master Alloy in A356.2 Alloy under Different Inoculated Temperatures and Holding Times