Abstract:Grain refinement of Zr–containing Al alloys has attracted extensive attention for many years in both industry and academia, since "Zr–poisoning" phenomenon always happens when commercial refiner is applied in such alloys. This unrecoverable grain nucleating obstacle finally leads to poor grain refinement efficiency. In this work, a special Al–Ti–C master alloy rich in TiC nano–particles was applied to a high–strength Al–Zn–Mg–Cu–Zr alloy (i.e. 7050 alloy). The effects of TiC nano–particles on the microstructure and mechanical properties of 7050 alloy during solidification, hot extrusion and subsequent heat treatment were systematically investigated. The results show that prominent grain refinement occurs with TiC addition through both the growth restriction effect and heterogeneous nucleation. Meanwhile, TiC nano–particles are more inclined to distribute along grain boundaries than the interior of matrix grains after solidification. After subsequent homogenization and hot extrusion, TiC nano–particles tend to align along extrusion direction. In comparison with 7050 matrix alloy, the tensile properties especially ductility of 1% TiCp/7050 composite after heat treatment have been improved obviously. Furthermore, it is worth noting that precipitates in the composite have also been obviously refined. Synergetic effects of grain refinement, refined precipitates and increased dislocation density are responsible for the optimized mechanical properties of TiCp/7050 composite. This work provides new insights for controlling matrix grains of Zr–containing Al alloys and developing low–cost Al matrix composites.

Effect of Al-3 wt% Al2O3 master alloy fabricated by calcined kaolin on grain refinement and mechanical properties of A356 alloy

Grain refinement of A356 alloy by Al–Ti–B–C master alloy and its effect on mechanical properties

Study on the Grain Refinement of A356 Alloy by Al–3 Wt-% VN Master Alloy

Research of Grain Refining on Pure Al by Three Different Master Alloys

Grain refinement and mechanical properties of Mg–5Li–3Al alloy inoculated by Al–5Ti–1B master alloy

Influence of Al-Ti-B Addition on the Microstructure and Mechanical Properties of A356 Alloys

Effect of Al–4Ti–5B master alloy on the grain refinement of AZ31 magnesium alloy

On the Understanding of Aluminum Grain Refinement by Al-Ti-B Type Master Alloys

STUDY ON THE MICROSTRUCTURES AND GRAIN REFINING PERFORMANCE OF Al-Ti-C GRAIN REFINING MASTER ALLOYS

Grain refinement and eutectic modification of A356 casting alloy by adding Al-B-Sr master alloys and its effect on tensile properties

Study on Grain Refinement and Refining Mechanism of Al-Si-Mg Alloy

Grain Refinement of Al-5Ti-0.62C-0.2Nd Grain Refiner for Commercial Pure Aluminum and Its Effect on Mechanical Properties

The Control of Nbb2 Particles in Al-Nbb2 Master Alloy and its Effect on Grain Refinement of Az91 Magnesium Alloy

Influences of Preparation Conditions and Melt Treatment Procedures on Melt Treatment Performance of Al-5Ti-B and Al-10Sr Master Alloys

Grain Refining Effects of Mn-30Al Master Alloy on Magnesium Alloy

Grain Refining Efficiency of Al-V-B Master Alloy in A356.2 Alloy under Different Inoculated Temperatures and Holding Times

Nucleation mechanism for grain refinement in A357 alloy by Al-Ti-B master alloys

Enhanced grain refinement and mechanical properties of a high–strength Al–Zn–Mg–Cu–Zr alloy induced by TiC nano–particles

Effect of Al–Er–Zr Master Alloy on Grain Refinement After Heat Treatment

Optimization of Processing Parameters for Preparation of Al-3Ti-1B Grain Refiner

The Behavior of AlTiC Master Alloys in Grain Refining of Commercial and High Pure Aluminum