Abstract:In ITER, the metallic first mirrors (FMs) will undergo erosion due to their proximity to the fusion plasma and deposition of materials originated from the first walls (mainly beryllium). In-situ plasma cleaning is a promising technique to conserve the FMs optical properties by means of ion sputtering. In this work, the evolution of the optical properties of single-crystal (Sc) and nanocrystalline (Nc) molybdenum (Mo) and rhodium (Rh) mirrors were investigated up to 100 cycles of consecutive contamination and cleaning. Aluminum oxide (Al 2 O 3 ) was used as contaminant to replace the toxic beryllium. The plasma cleaning was carried out using a capacitively coupled argon (Ar) plasma excited by a 60 MHz radio-frequency generator resulting in the formation of a self-bias applied on the mirrors of -280 V. The plasma potential being around 30 V, the Ar ion energy was about 310 eV. The optical properties of the mirrors were assessed using ex-situ reflectivity measurements. Moreover, the surface topography was characterized by means of scanning electron microscopy (SEM), focused ion beam (FIB) and roughness measurements using atomic force microscopy (AFM). ScMo and ScRh mirrors formerly exposed to 80 successful cleaning cycles using aluminum/tungsten (Al/W) deposits and air storage exhibit drastic changes in their optical properties after being subject to cleaning cycles using Al 2 O 3 as contaminant. Additionally, freshly polished ScRh were exposed to identical cleaning cycles. All Sc mirrors exhibited pits induced by the polishing procedure using diamond paste in addition of mounds/wavy patterns. The carbon incorporated during the polishing process was demonstrated to be responsible for the pitting of the surface. The Nc mirrors preserved their initial reflectivities after up to 100 cycles. The surface topography was systematically characterized and an average erosion rate for NcRh mirrors of about 59 nm per cycle has been estimated from FIB cross-sections. The optical properties of the Nc mirrors showed a superiority in the present study in comparison to the Sc materials due to the influence of their polishing procedures.

Monitored wet-etch removal of individual dielectric layers from high-finesse Bragg mirrors

A novel trilayer antireflection coating using dip-coating technique

Anti-reflection Coating at 550 Nm Fabricated by Atomic Layer Deposition

Traceless Mitigation of Laser Damage Precursors on a Fused Silica Surface by Combining Reactive Ion Beam Etching with Dynamic Chemical Etching

Fabrication of mirror templates in silica with micron-sized radii of curvature

Fabrication and Analysis of a Fabry-Perot Cavity with a Micromechanical Wet-Etching Process.

Tuning the peak position of subwavelength silica nanosphere broadband antireflection coatings.

Novel Method of Fabricating Fabry-Perot Cavity Employing MEMS Wet-Etching Process

An Optical Monitoring Method for Depositing Dielectric Layers of Arbitrary Thickness Using Reciprocal of Transmittance

Deep reactive ion etched anti-reflection coatings for sub-millimeter silicon optics

Morphological modification of Rh-C coatings upon low-energy Ar + ion sputtering

The Sacrificial Layer Releasing of Micro-Machined Optical-Fiber Switch with Poly-Si Torsion Mirror

Experimental Study on Roughness and Flatness of Micromirror Fabricated by Different Anisotropic Silicon Etching Processes

Evaluating the use of self-assembled monolayer (SAM) release coatings for replicated optics

Surface modification of ITER-like mirrors after one hundred cleaning cycles using radio-frequency plasma

Impact of laser-contaminant interaction on the performance of the protective capping layer of 1 ω high-reflection mirror coatings

Study of Ion-Assisted E-Beam Evaporation Coating Process on Chirped Mirrors

High finesse opto-mechanical cavity with a movable thirty-micron-size mirror

Miniature tapered photonic crystal fiber interferometer with enhanced sensitivity by acid microdroplets etching.

Sub-damage-threshold plasma etching and profile tailoring of Si through laser-stimulated thermal desorption

Mid-infrared monocrystalline interference coatings with excess optical loss below 10 ppm