Abstract:Heterogeneous microstructure designs have attracted a great deal of attention, not only because they have the potential to achieve an ideal combination of two conflicting properties, but also because the processes involved in their fabrication are cost-effective and can be scaled up for industrial production. The process parameters in the preparation process have an important effect on the microstructure and properties of alloy members prepared by wire arc additive manufacturing (WAAM) technology. It was expected that the spatial heterogeneous microstructure with large microstructural heterogeneities in metals can be formed through changing the process parameters. In this work, homogeneous NiTi thin-walled component and heterogeneous NiTi thin-walled component were fabricated using WAAM technology by adjusting the heat input. The effects of deposition height and heat input on the microstructure, mechanical properties and wear properties of WAAM NiTi alloys were investigated. The results show that grains were gradually refined with the increase of deposition height in the homogeneous WAAM NiTi component. The ultimate tensile strength of homogeneous WAAM NiTi component increased from 606.87 MPa to 654.45 MPa and the elongation increased from 12.72% to 15.38%, as the increase of deposition height. Moreover, the homogeneous WAAM NiTi component exhibited excellent wear resistance, the coefficient of friction decreased from 0.760 to 0.715 with the increase of deposition height. Meanwhile, the grains in the heterogeneous WAAM NiTi component shows the finest grains in the central region. The ultimate tensile strength of the lower region, middle region and upper region of heterogeneous WAAM NiTi components were 556.12MPa, 599.53MPa and 739.79MPa, and the elongations were 12.98%, 16.69%, 21.74%, respectively. The coefficient of friction for the lower region, middle region and upper region of heterogeneous WAAM NiTi components were 0.713, 0.720 and 0.715, respectively. The microhardness and cyclic compression properties of the homogeneous components with higher heat input were better than those of the heterogeneous components for the same deposition height. The tensile yield strength, elongation and wear resistance of the heterogeneous components were superior compared to the homogeneous components. These results can be used to optimize the WAAM process parameters to prepare NiTi components with excellent mechanical properties.

Studies on wire hot extrusion processes of metals and metal/CNT

MICROSTRUCTURES AND PROPERTIES OF HOT-EXTRUDED SiCW/6061Al COMPOSITES

Progress and Current Status in Research on Nanostructured Cu-Ag Microcomposites for Conductor Wires

Microstructure and Properties of Cold Drawing Cu-2.5% Fe-0.2% Cr and Cu-6% Fe Alloys

Experimental and Numerical Study on Friction and Wear Performance of Hot Extrusion Die Materials

Influences of Fe Content and Cold Drawing Strain on the Microstructure and Properties of Powder Metallurgy Cu-Fe Alloy Wire

Numerical simulation of friction extrusion: process characteristics and material deformation due to friction

Relationships between mechanical strength and electrical conductivity for Cu–Ag filamentary microcomposites

Effect of hot extrusion on the microstructure and mechanical properties of SiCNWs/Mg-2Zn-0.1Y composite

Novel approach to optimize the mechanical properties of Cu-Al composite wires

Microstructure and properties of nanofilament Cu-Nb and Cu-Ag composites

Effect of C-Mn-Cu on microstructure and properties of wire arc additive manufacturing of high-manganese steels

Analysis of Deformation Behaviour and Residual Stress in Rotary Swaged Cu/Al Clad Composite Wires

Fabrication of a novel high-strength and high-conductivity copper-clad aluminum composite wire

Microstructure and properties research of Al-Zn-Mg-Cu alloy with high strength and high elongation fabricated by wire arc additive manufacturing

Multiscale modelling of microstructure, micro-segregation, and local mechanical properties of Al-Cu alloys in wire and arc additive manufacturing

Influence of Nb Morphology on the Structure and Properties of High Strength and High Conductivity Cu-Nb Composite Wires

10.1063/1.5084134.2

Revealing microstructural evolutions, mechanical properties and wear performance of wire arc additive manufacturing homogeneous and heterogeneous NiTi alloy

Re -dissolution behavior of secondary phases and mechanical response of CNT/2024Al composites

Impact tension behavior of heavy-drawn nanocrystalline CoCrNi medium entropy alloy wire