Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Novel precursor-derived Al–C–N–(O)-based ceramic additive for the low-temperature pressureless sintering of silicon nitride

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Synthesis of MgO-CaO-Al 2 O 3 -Sio 2 Nanocomposite Powder by Polymeric Complex Method As a Novel Sintering Additive of AlN Ceramics

High Thermal Conductivity Silicon Nitride Ceramics Prepared By Pressureless Sintering With Ternary Sintering Additives

Preparation of SiC-AlN Ceramic Alloy Powder by Direct Reaction Between Constituent Elements and Property Evaluation of Its Sintered Compacts.

Fabrication of novel AlN-SiC-C refractories by nitrogen gas-pressure sintering of Al4SiC4

Pressureless Sintering and Properties Investigation of Silicon Nitride

Synthesis of SiC-AlN Ceramic Alloy Powder by the Direct Reactions Between the Constituent Elements.

Synthesis of Fibrous Β-Si3n4 Structured Porous Ceramics Using Carbothermal Nitridation of Silica

Preparation of silicon nitride fibers by additive-assisted nitridation of polysilicon waste powder

A New Sintering Additive for Silicon Carbide Ceramic

Preheating-assisted Combustion Synthesis of Β-Si3n4 Powders at Low N2 Pressure

Synthesis of Si 3 N 4 powder with tunable α/β-Si 3 N 4 content from waste silica fume using carbothermal reduction nitridation

Effect of Multi-Sintering Additive MgO-Al2O3-CeO2 on Densification and Properties of Silicon Nitride Ceramics by Spark Plasma Sintering

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Fabrication of low-shrinkage, porous silicon nitride ceramics by addition of a small amount of carbon

Preparation and mechanical properties of SiC-AlN ceramic alloy

Low temperature fabrication of highly dense α‐Si3N4 ceramics

Preparation and properties of Si3N4 ceramics via digital light processing using Si3N4 powder coated with Al2O3-Y2O3 sintering additives

Effects of AlN inorganic binder on the properties of porous Si3N4 ceramics prepared by selective laser sintering

Cost-effective manufacture and synthesis mechanism of ferrosilicon nitride porous ceramic with interlocking structure