Abstract:The hot deformation characteristics. of as-cast nickel-base superalloy GH742y after hot isostatic pressing (HIP)(hereafter referred to as-cast alloy) have been investigated by hot compression tests in the temperature range of 1050 to 1140 degrees C, strain rate range of 0.01 s(-1) to 10 s(-1) and strain range of 35% to 50% by means of Gleeble-3500 thermal mechanical simulator. The results show that the as-cast alloy exhibits the poor deformability,and shows wedge-shaped cracking beyond the strain of 35%. At strain rates less than 1.0 s(-1), the stress-strain curves exhibit nearly steady-state behavior, while at strain rate of 10 s(-1), a yield drop and serrated yielding occur. The activation energy values developed on the basis of the experimental data are divided into three domains. The first domain appears at lower strain rate (<= 1.0 s(-1)) and lower temperature (<= 1080 degrees C), with the lowest mean value of activation energy about 261.4 kJ/mol. The second domain appears at the same strain rate as the first domain, but higher temperature (>1080 degrees C), with the intermediate mean value of activation energy about 328.8 kJ/mol. The third domain appears at higher strain rate (10 s(-1)) and temperature range of 1050 to 1140 degrees C, with the largest mean value of activation energy about 605.05 kJ/mol. Three different constitutive equations are established in corresponding to domains. Microstructural observations in the third domain reveal non-uniform dynamic recrystallization (DRX) of homogeneous gamma phase, which leads to the poor deformability and the highest Q value. In contrast, microstructures in the first domain show fully DRX of homogeneous gamma phase, leading to the better deformability and the lowest Q value. It is noted that the grain size increases with the increment of strain rate or temperature. These results suggest that bulk metal working of this material may be carried out in the first domain where fully DRX of gamma homogeneous occurred.

Hot oscillating pressed FGH4096 nickel-based alloy with enhanced ductility and strength

Hot oscillatory pressure preparing low-cost FGH4096 superalloys with high performance

Microstructure and properties of AlCoCrNiFe high-entropy alloy sintered by hot oscillating pressing

Markedly enhancing mechanical properties of powder metallurgy superalloy by hot oscillatory forging

Investigation of a Hot-Pressed Nb–Ti–Al Alloy: Mechanical Alloying, Microstructure and Mechanical Property

Hot oscillatory pressure sintered W–Ni–Fe refractory alloy under different sintering pressures: Microstructures, densification behavior and properties

W‐Ni‐Fe refractory alloy sintered by hot oscillating pressure under different amplitudes

Influence of sintering temperature on microstructure and properties of 90W-10Ti alloy targets prepared by hot oscillating pressing

Effect of hot isostatic pressing on microstructures and properties of superalloy K4169

Quantitative and Qualitative Characterization of the Damage, Deformation Mechanisms, and Failure Modes of a Nickel-Based GH3536 Alloy Prepared Via Laser Powder Bed Fusion after Various Heat Treatments

Additively manufactured oxide dispersion strengthened nickel-based superalloy with superior high temperature properties

Microstructures and Properties of AlCoCrNiFe High-Entropy Alloy Sintered by Hot Oscillating Pressing Under Different Sintering Times

Thermal processing behaviour and microstructural evolution of high W and high γ' content extruded nickel-based powder metallurgy superalloy FGH4109

Sintering process in hot oscillatory pressure of 90W–7Ni–3Fe refractory alloy at different time

Hot Compressive Deformation Behavior and Microstructure Evolution of HIPed FGH96 Superalloy

Hot Deformation Characteristics for a Nickel-base Superalloy GH742y

Hot oscillatory pressing of B 4 C ceramics for improving densification and mechanical properties

Hot deformation behavior and microstructure evolution of NiAl-9HfO<sub>2</sub> composite

Hot Deformation Behavior of the Ti6Al4V Alloy Prepared by Powder Hot Isostatic Pressing

Near‐Net Shape Hot Isostatic Pressing: Microstructural Analysis and Hardness Evolution at a Steel–Nickel Alloy Interface

Hot deformation behavior and microstructure evolution of a novel nickel-based powder metallurgy superalloy