Abstract:Quantum metrological standards based on the fundamental physical constants are the trend of modern metrology because of their attributes such as high accuracy, high stability, and good reproducibility. The quantum Hall effect (QHE), which refers to the electronic charge e and the Planck constant h, is used to define the quantum resistance standard. The quantum Hall resistance (R-H) of h/2e(2) at the filling factori = 2 is used as the standard. It is obvious that the RH is non-integral. However the resistors that need to be calibrated each have a decimal value, such as 1 k Omega, 10 k Omega, 100 k Omega, etc. The calibration chain from the non-integral R-H to the real resistor is long. The quantum Hall array resistance standards (QHARSs) are invented to solve this problem. The QHARS which are based on the decimal resistance values can shorten the calibration chain, improve the resistance transfer accuracy, and finally realize the quantization of the whole resistance calibration chain. The QHARS can also replace the traditional physical transfer standard resistor and realize the quantization of the transfer standard resistor. The decimal QHARS devices can be realized by connecting single QHE devices in series or parallel with the multiple link technology.In this paper we report the design, fabrication and characterization of a 1 k Omega QHARS device based on the GaAs/AlxGa1-x As heterostructures. In our design, the 1 k Omega array device consists of only 29 Hall bars. The nominal value of the device is 999.9999658 Omega with a relative deviation of -3.42 x 10(-8) from 1 k Omega. The ratio between the maximum and minimum current flowing through the Hall bars is as small as 14.5.The 1 k Omega QHARS devices are measured in the national resistance standard system at a temperature of 1.5 K. The measurement is taken at the central magnetic field of the 2nd quantum Hall plateau. We compare our 1 k Omega QHARS resistor with a 1 k Omega transfer standard resistor using the direct current comparator. The 1 k Omega transfer standard resistor has already been calibrated in advance with our single QHR standard by cryogenic current comparator. Therefore the resistance of our 1 k Omega QHARS resistor can be obtained. The relative deviation between the measured resistance value and the designed value is -1.96 x 10(-7) with a standard uncertainty of 2.07 x 10(-7). The results show that we have realized the 1 k Omega quantum Hall resistance standard device which can be used for the resistance calibration.

1 Ω-10 kΩ high precision transportable setup to calibrate multifunction electrical instruments

Resistance standards with calculable, nearly negligible AC-DC difference at frequencies up to 2 MHz for the calibration of precision LCR meters

Automated Setup to Accurately Calibrate Electrical DC Voltage Generators

Measurement of Resistance Standards by a Precision LCR Meter at Frequencies up to 2 MHz

Wideband Current Transducer Traceable Calibration up to 10 A and 1 MHz

High precision measurement of the load effect of the resistor

Wide-Range Digital-Analog Mixed Calibration Technology of a DC Instrument Transformer Test Set

A 1 K Omega Standardresistor Device Based On Quantum Hall Array

Thermoelectric Sensors as Microcalorimeter Load

Development of Calibration Source for Dynamic Contact Resistance Tester of Conductive Ring Based on Time-Varying Resistance

Study on the Calibration of Partial Discharge Calibrators of Charge from 0.1pc to 10Nc

Multichannel Emulator for Resistance Temperature Detectors (RTDs)

Development of a Wide-range AO Kelvin Bridge

Development and implementation of an automated four-terminal-pair Josephson impedance bridge

Improved Static Testing of A/D Converters for DC Measurements

Characterization of High Temperature Calibration Bath through Stability and Uniformity Tests with Data Acquisition using Standard Platinum Resistance Thermometer and Precision Multimeter

Bilateral comparison of 1.018 V and 10 V standards between INRIM (Italy) and the BIPM, November to December 2023 (part of the ongoing BIPM key comparison BIPM.EM-K11.a and b)

Calibration System for High-Voltage Transformers With Multiharmonic Distorted Waveforms

Validation of the Reference Impedance in Multiline Calibration with Stepped Impedance Standards

Highly precise nonlinear error calibrating system based on Fabry-Perot interferometer - art. no. 68342X

Metal-carbon eutectic high temperature fixed points for in-situ calibration of radiation thermometers