Abstract:The evolution of phase composition and mechanical properties and the formation of oxide layers on Fe40–xNiCoCrAlx (x = 5 and 10 at.%) alloys in long-term oxidation at 900 and 1000°C were studied. In the initial cast state, depending on the aluminum content and valence electron concentration, the alloys contain only an fcc solid solution (VEC = 8 e/a) or a mixture of fcc and bcc phases (VEC = = 7.75 e/a). Thin continuous oxide scales containing Cr2O3 and NiCr2O4 spinel formed on the surface of both alloys oxidized at 900°C for 50 h. A further increase in the annealing time to 100 h leads to the formation of aluminum oxide Al2O3 in the scale on the Fe30Ni25Co15Cr20Al10 alloy, having high protective properties. An increase in the oxidation temperature to 1000°C results in partial failure of the protective layer on the alloy with 10 at.% Al. Long-term holding at 900°C (100 h) + 1000°C (50 h) does not change the phase composition of the Fe35Ni25Co15Cr20Al5 alloy matrix, being indicative of its high thermal stability. In the two-phase Fe30Ni25Co15Cr20Al10 alloy, the quantitative ratio of solid solutions sharply changes: the amount of the bcc phase increases from 4 to 54 wt.% and its B2-type ordering is observed. The mechanical characteristics of the starting alloys and those after long-term high-temperature annealing were determined by automated indentation. The hardness (HIT) and elastic modulus (E) of the cast Fe35Ni25Co15Cr20Al5 alloy are equal to 2 and 147 GPa, respectively, and decrease to 1.8 and 106 GPa after a series of long-term annealing operations. The Fe30Ni25Co15Cr20Al10 alloy shows the opposite dependence: HIT increases from 2.5 in the initial state to 3.1 GPa after annealing and E decreases from 152 to 134 GPa. This indicates that the Fe30Ni25Co15Cr20Al10 alloy is promising as a high-temperature oxidation-resistant and creep-resistant material.

Mechanical Characterisation of the Protective Al$_2$O$_3$ Scale in Cr$_2$AlC MAX phases

Microstructural and compositional design of Cr2AlC MAX phases and their impact on oxidation resistance

Ultrahigh strength-ductility of nanocrystalline Cr 2 AlC coating under micropillar compression

Manufacturing of High Purity Cr2AlC MAX Phase Material and Its Characterization

Mechanical and Oxidation Behavior of Textured Ti2AlC and Ti3AlC2 MAX Phase Materials

Ion Irradiation Induced Softening in Cr2AlC MAX Phase

Microstructure and Oxidation Behaviors of (TiVCr)2AlC MAX-Phase Coatings Prepared by Magnetron Sputtering

On the determination of the thermal shock parameter of MAX phases: A combined experimental-computational study

Shear and delamination behaviour of basal planes in Zr3AlC2 MAX phase studied by micromechanical testing

Mechanical behavior, bonding nature, and defect processes of Mo2ScAlC2: a new ordered MAX phase

Microstructure evolution of Cr 2 AlC MAX phase under a graphite bed between 1100 °C and 1500 °C

Preparation and performance of MAX phase Ti3AlC2 by in-situ reaction of Ti-Al-C system

Microstructure evolution and elemental diffusion behavior near the interface of Cr2AlC and single crystal superalloy DD5 at elevated temperatures

High Temperature Effects on Irradiation Damage of Ti2AlC

Synthesis and Mechanical Properties of High-Purity Cr2alc Ceramic

Crystal Structure and Elastic Properties of Hypothesized MAX Phase-like Compound (Cr2Hf)2Al3C3

On Extracting Mechanical Properties from Nanoindentation at Temperatures up to 1000$^{\circ}$C

Structural State of High-Entropy Fe40–xNiCoCrAlx Alloys in High-Temperature Oxidation

Effect of oxygen substitution and oxycarbide formation on oxidation of Ti3AlC2 MAX phase

The effect of milling time and heat treatment on the synthesis of the Cr2AlC MAX phase

Structural, elastic, mechanical, electronic, damage tolerance, fracture toughness, and optical properties of Cr–Al–B MAB phases studied by first-principles calculations