Abstract:Abstract Introduction Dermatomes are widely used for split thickness skin graft harvest and are regarded as the optimal means of obtaining a graft of the desired thickness. The harvested graft thickness depends in part on the cut thickness setting, adjusted using a dial on the dermatome, according to increments in thousandths of an inch, or millimetres. Previous authors have described a simple “on table” technique which uses a standard scalpel blade as a calibration tool to determine cut thickness immediately prior to graft harvest. This study aims to assess how reliable and consistent the dial on the dermatome is, and whether a #15 surgical blade placed in the dermatome blade aperture may be used to set or confirm the cut thickness. In addition, whether any statistical or clinical difference exists between the blade-measured aperture and the stated aperture using either the cutting (belly) or non-cutting edge (spine) of the scalpel, as well as the intra- and inter-rater reliability of the technique. Methods The precise thickness of #15 surgical blades (N=10) was first measured using an electronic micrometer. Six working dermatomes, loaded with a four inch guard, were each assessed by two surgeons in triplicate using both the belly and spine of the blade. The endpoint was the smallest cut thickness setting that would permit passage of an entire surgical blade through the dermatome aperture, starting from zero and increasing cut thickness at intervals of 1/1000 in. Results The mean measured #15 scalpel blade thickness was 0.391 mm (range 0.381-0.408 mm), or 16/1000 in. The mean cut thickness setting, of all 72 measurements, which would permit the blade was 6.0/1000 in (SD = 1.6/1000 in). This was a mean difference of 10/1000 in from the measured thickness of a #15 scalpel blade, one-way ANOVA p< 0.001. Individual dermatome apertures differed, ranging from a mean of 5.0 to 7.8/1000 in, ANOVA p< 0.001. Intra-rater reliability of this technique was excellent (ICC = 0.89), however inter-rater reliability was only fair (ICC = 0.52), with a mean difference of 1.5/1000 between surgeons (6.8 vs 5.2/1000 in, t-test p< 0.018). The mean difference between passing the belly versus the spine of the blade was not significant, 0.47/1000 in, t-test p=0.474. Conclusions Testing the aperture opening with a #15 blade is a more consistent measurement of thickness then reading the number on the dial of the dermatome. A clinically significant difference exists between the thickness of a #15 surgical blade and the stated cut thickness of a dermatome. This ad hoc calibration technique has only modest reliability between individuals, however the difference in thickness may not be clinically significant. Using the belly or spine of the scalpel produces similar results. Applicability of Research to Practice The test is a simple and reproducible manoeuvre to calibrate a dermatome, however there appears to be a large discrepancy between the stated cut thickness and physical dimensions of a scalpel blade.

Experimental evaluation of two current-generation automated microkeratomes: the Hansatome and the Supratome

Evaluation of Morphological Features: Femtosecond-Lasik Flap Vs. SMILE Cap, and the Effects on Corneal Higher-Order Aberrations.

LASIK flap thickness profile and reproducibility of the standard vs zero compression Hansatome microkeratomes: three-dimensional display with Artemis VHF digital ultrasound

Predictability of corneal flap in laser in situ keratomileusis with disposable M2 130 and 90 microkeratome heads

Comparison of corneal flap morphology using AS-OCT in LASIK with the WaveLight FS200 femtosecond laser versus a mechanical microkeratome.

Study of KN-5000 Microkeratome for Lasik

Comparison of corneal flap morphology in laser in situ keratomileusis with the WaveLight femtosecond laser versus the Moria mechanical microkeratome

Anterior Segment Optical Coherence Tomography Measurement of Flap Thickness after Myopic LASIK Using the Moria One Use-Plus Microkeratome

[Analysis of Flap Thickness by Anterior Segment Optical Coherence Tomography in Different Flap Preparation Styles of Excimer Laser Surgery].

The Impact Of Flap Creation Methods For Sub-Bowman'S Keratomileusis (Sbk) On The Central Thickness Of Bowman'S Layer

Experimental Rationale for Using an Eximer Laser for Preparation of Ultrathin Graft for Posterior Lamellar Keratoplasty

An Experimental Study on the Separation of Human Corneal Epithelium with Different Blade Edge Sharpness of the Ultra-thin Microkeratome

Clinical research of KM-5000D automatic microkeratome for making corneal flap in LASIK

Femtosecond laser versus mechanical microkeratome: a retrospective comparison of visual outcomes at 3 months

Comparison of corneaI biomechanicaI changes at earIy stage after femtosecond LASIK and microkeratome LASIK

Examination of phacoemulsification tips after different numbers of cataract surgeries

Topographical and histological analysis of keratinized mucosal grafts removal techniques an ex-vivo study in porcine mandibles

656 Inter- and Intra-user Reliability of Skin Graft Thickness as a Function of Instrument

78 Assessment of the Scalpel Blade as a Calibration Tool for Measuring Dermatome Cut Thickness

Comparison of modern high-speed vitrectomy systems and the advantages of using dual-bladed probes

Excimer Laser-Assisted Deep Anterior Lamellar Keratoplasty Versus Penetrating Keratoplasty for Patients With Keratoconus: A Retrospective Analysis From the Homburg Keratoconus Center