Abstract:A Ni‐based interlayer alloy is designed for transient liquid phase bonding of ZGH451 superalloy produced through directed energy deposition. Joints with a controlled gap within the range of 0–30 μm achieve complete isothermal solidification, exhibiting up to 1375 MPa tensile strength at room temperature and 983 MPa at 760 °C. Notably, the interlayer alloy developed in this study outperforms the conventional BNi‐2. ZGH451, a directionally solidified Ni‐based superalloy designed for additive manufacturing, has garnered significant attention in the realm of next‐generation turbine blades. Welding the ZGH451 superalloy is crucial for promoting its practical application. In this study, transient liquid phase (TLP) bonding is applied to weld ZGH451 superalloy produced through directed energy deposition. A Ni‐based interlayer alloy powder is developed and prepared via thermodynamic calculation, with the interlayer subsequently characterized using differential thermal analysis. TLP bonding is conducted at 1200 °C for 4 h. The influence of the preset gap on the joint microstructure and mechanical properties is examined. The microstructure of the TLP bonding joints comprises athermally solidified zones (ASZ), isothermally solidified zones, and diffusion‐affected zones. The ASZ width significantly increases with the growing preset gap. A preset gap not exceeding 100 μm enables complete isothermal solidification of the joints. Particularly, joints with a preset gap ranging from 0 to 30 μm demonstrate optimal reliability, exhibiting a tensile strength of up to 1375 MPa at room temperature, which is 12% higher than the room temperature strength of the base metal (BM), and a tensile strength of 983 MPa at 760 °C, surpassing 86% of the BM's strength at the same temperature.

Ultrafast and robust joining of 3YSZ and GH3128 superalloy using Cu interlayer under an electric field

Electrochemical wetting of 3YSZ by Cu and ultrafast joining with a Ni-based superalloy

Electrochemically driven rapid wetting of 3YSZ by 60Cu–40Ag and its robust joining to 304 stainless steel

Flash sintering of 3YSZ and in-situ joining with 304 stainless steel using copper as an interlayer

Fast joining of 8YSZ to NiCrFe medium-entropy alloy by using an electric field

Flash joining of 3YSZ and 430 SS using Ag–CuO filler

Low-temperature direct diffusion bonding of Zr702 alloys via electric current assistance

Near-seamless joining of Cf/SiC composites using Y3Si2C2 via electric field-assisted sintering technique

Rapidly Achieving a Reliable Full-Ceramic Interface of ZrC-SiC Composite Using Ti Interlayer Via Pulsed Electric Current Joining

A Low-Temperature Strategy to Rapidly Prepare High-Quality Diffusion-Bonded Joint of Dissimilar Superalloys Enabled by Pulsed Current

Diffusion Brazing of GH536 Polycrystalline Superalloy with IC10 Single Crystal Superalloy Using BNi-2 Interlayer

Flash joining of Y2O3 transparent ceramic to titanium alloy

Transient Liquid Phase Bonding of ZGH451 Superalloy Fabricated by Directed Energy Deposition

Robust Joining of FGH98 Superalloy to DD5 Single Crystal by Modulating Interdiffusion Behavior with Ni/high-entropy Alloy Hybrid Interlayer

Electrochemically enhanced wetting of 3YSZ and Mn1.5Co1.5O4 by Ag−CuO and their application in flash joining

Joining C/C composite in a few seconds using refectory high entropy alloy fillers via spark plasma sintering

Ultrafast High-Temperature Joining of Ti3SiC2 Using FeCoCrNiCu High-Entropy Alloy Via Thermal Shock

Joining zirconia with nickel-based superalloys for extreme applications by using a pressure-free high-temperature resistant adhesive

Joining of Yttria Stabilised Zirconia to Ti6Al4V Alloy Using Novel CuO Nanostructure Reinforced Cu Foam Interlayer

Joining 3YSZ Electrolyte to AISI 441 Interconnect Using the Ag Particle Interlayer: Enhanced Mechanical and Aging Properties

Interfacial Microstructure and Mechanical Properties of ZrB2SiC C Ceramic and GH99 Superalloy Joints Brazed with a Ti-modified FeCoNiCrCu High-Entropy Alloy