Abstract:Manganese-Cobalt Oxide (MCO) spinel oxide is a promising composition as a protective coating for the metallic interconnects of a SOFC. In an effort to reach better properties, such as suitable thermal expansion match, good electrical conductivity, and fine structural stability, various elements have been doped in the spinel structure. In this study, the effect of Cu addition as a dopant on the electrical properties of MCO spinel is investigated. Powders with a nominal composition Cux(Mn1.5-x/2Co1.5-x/2)O4 (x=0, 0.15, and 0.3) were successfully synthesized based on the sol-gel Pechini method. The phase composition and microstructure of the synthesized powder were characterized by X-ray diffraction (XRD) and field emission scanning electron microscopy (FESEM). The XRD results revealed that a pure phase with a spinel structure was obtained for different amounts of doped samples. The microstructural characteristics of the synthesized powders revealed that the average particle size of the powder decreased from about 84nm to 52nm with the introduction of Cu. To evaluate the effect of Cu on the sintering behavior of MCO, the powder was pressed and sintered at 1200°C for 2h. The density measurement and FESEM results showed that the addition of Cu promotes the sintering mechanism, and the density was improved. In addition, the electrical properties of the samples were evaluated using the 2probe direct current technique at different temperatures. The results revealed that the addition of 0.3 Cu increased the electrical conductivity of the sample from 0.102 to 0.218 S.cm-1 at 800°C. This significant improvement can be attributed to the promotion of sintering and also facilitating electron flow by substitution of Cu+2 cations in the spinel structure.

Electrochemically enhanced wetting of 3YSZ and Mn1.5Co1.5O4 by Ag−CuO and their application in flash joining

Electrochemically driven rapid wetting of 3YSZ by 60Cu–40Ag and its robust joining to 304 stainless steel

Electrochemical wetting of 3YSZ by Cu and ultrafast joining with a Ni-based superalloy

Flash joining of 3YSZ and 430 SS using Ag–CuO filler

Flash sintering of 3YSZ and in-situ joining with 304 stainless steel using copper as an interlayer

Supersonic spray derived Cu–Co oxide coating on SUS441 to protect the metallic interconnect and to increase stability of SOFC cathode

Cu and Y doped (Co, Mn)3O4 spinel coatings on Crofer ferritic alloy by composite electrodeposition

Mn–Co spinel protective–conductive coating on AL453 ferritic stainless steel for IT-SOFC interconnect applications

Fabrication of Dense La0.7Ca0.3Cr0.97O3-delta Interconnect Thin Membrane on Composite Anode Support by Co-firing

The electrical property of MnCo2O4 and its application for SUS 430 metallic interconnect

Plasma spray coating on interconnector toward promoted solid oxide fuel cells and solid oxide electrolysis cells

Preparation, Evaluation, and Application of SUS430/441 Interconnect with Mn-Co Coating in Solid Oxide Fuel Cells

Cu doped Mn-Co spinel protective coating on ferritic stainless steels for SOFC interconnect applications

High-entropy FeCoNiMnCu alloy coating on ferritic stainless steel for solid oxide fuel cell interconnects

Evaluation of the Reactive-Sintered (mn,co)3o4 Spinel Layer for SOFC Cathode-Side Contact Application

Ultrafast and robust joining of 3YSZ and GH3128 superalloy using Cu interlayer under an electric field

Performance of stainless steel interconnects with (Mn,Co)3O4-Based coating for solid oxide electrolysis

Characterization of La0.8Sr0.2Co0.5Mn0.5O3-δ Coating on Alloy Interconnect in SOFC

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

Pulsed current-driven wetting of 3YSZ by liquid Cu and its mechanisms

Synthesis and characterization of nanostructured Cux (Mn1.5-x/2Co1.5-x/2)O4 as an interconnect coating for solid oxide fuel cell