Abstract:Copper sulfides (Cu2–xS) have become potential thermoelectric (TE) materials because of their high element abundance, low toxicity, and high performance. A series of Cu1.8–2xBi2xS1–3xSe3x (0 ≤ x ≤ 0.03) bulks were fabricated using mechanical alloying and spark plasma sintering. The main Cu1.8S phase was obtained in all compositions of 0 ≤ x ≤ 0.03, and marginal Cu1.96S and Cu2S phases were detected at 0.02 ≤ x ≤ 0.03, which is attributed to the volatilization of sulfur and selenium. Benefiting from the introduced extra electronics by Bi3+ doping, the carrier concentration was optimized in 2.31×1021 cm–3. Multiscale defects introduced by Bi–Se co-doping, including secondary phases, micropores, and point defects (BiCu••, SeS×, and VS••), strongly scattered the phonons, leading to a drastically decreased thermal conductivity from 2.71 W m–1 K–1 for Cu1.8S at 773 K to 0.80 Wm–1 K–1 for Cu1.74Bi0.06S0.91Se0.09. A maximum ZT of 0.78 was achieved for Cu1.74Bi0.06S0.91Se0.09 at 773 K, which is 144% higher than that of Cu1.8S (0.32). The current stress test confirms that Bi doping could improve the stability of Cu1.8S by suppressing the Cu ion migration. Our work demonstrates that Bi–Se co-doping is an effective way to enhance the TE properties for Cu1.8S.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00414.SPB model calculation of our work; method for the current stress test; calculation formulas for ZTeng and ηmax; temperature dependence of thermal properties of the Cu1.8–2xBi2xS1–3xSe3x (x = 0, 0.01, 0.02, 0.25, 0.03) samples; and repeatability test of electrical properties for the Cu1.74Bi0.06S0.91Se0.09 sample (PDF)This article has not yet been cited by other publications.

Modification of the thermoelectric performance in Se alloyed CoSb1-xSexS

Enhanced thermoelectric performance of CoSbS via Se doping at dual Sb and S sites

High Pressure Synthesis and Thermoelectric Performance of CoSbS1-xSex (x=0 similar to 0.3)

Mid-temperature Thermoelectric Performance of Zone-Melted Sb2(Te,Se)3 Alloys Near Phase Transition Boundary

Improved Thermoelectric Properties of Bi2Te3−xSexalloys by Melt Spinning and Resistance Pressing Sintering

Realizing the Ultralow Lattice Thermal Conductivity of Cu3SbSe4 Compound via Sulfur Alloying Effect

Enhanced Thermoelectric Performance of SmS by Se Alloying and Y Doping

Enhanced Thermoelectric Performance of Ag0.8Pb18SbTe20 Alloyed with Se

Enhanced thermoelectric performance of BiCuSO by Pb doping and Se alloying

Enhanced Thermoelectric Performance of Cu2Se Alloys by Simultaneous Engineering of Thermal and Electrical Transport Properties Through S and Te co‐doping

Realizing Enhanced Thermoelectric Performance and Hardness in Icosahedral Cu 5 FeS 4− x Se x with High‐Density Twin Boundaries

Enhanced Thermoelectric Performance Through Tuning Bonding Energy in Cu2Se1–xSx Liquid-like Materials

Ultralow Thermal Conductivity and Enhanced Figure of Merit for CuSbSe2 Via Cd-Doping

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu 1.8 S via Carrier Concentration Regulation and Multiscale Phonon Scattering

Thermoelectric SnS and SnS-SnSe Solid Solutions Prepared by Mechanical Alloying and Spark Plasma Sintering: Anisotropic Thermoelectric Properties.

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu1.8S Via Carrier Concentration Regulation and Multiscale Phonon Scattering

Thermoelectric Properties of PbSe-PbS Solid Solutions Prepared by Mechanical Alloying Method and High Pressure Sintering

Thermoelectric Performance Enhancement of Cu2S by Se Doping Leading to a Simultaneous Power Factor Increase and Thermal Conductivity Reduction

Enhanced Thermoelectric Properties in Highly Co-Doped Bi2Se3 by Density-of-State Effective Mass Increase

Synthesis of SnSe 1– x S x Polycrystals with Enhanced Thermoelectric Properties Via Hydrothermal Methods Combined with Spark Plasma Sintering

Enhanced Thermoelectric Performance of Nonstoichiometric Compounds Cu3−x SbSe4 by Cu Deficiencies