Abstract:Copper sulfides (Cu2–xS) have become potential thermoelectric (TE) materials because of their high element abundance, low toxicity, and high performance. A series of Cu1.8–2xBi2xS1–3xSe3x (0 ≤ x ≤ 0.03) bulks were fabricated using mechanical alloying and spark plasma sintering. The main Cu1.8S phase was obtained in all compositions of 0 ≤ x ≤ 0.03, and marginal Cu1.96S and Cu2S phases were detected at 0.02 ≤ x ≤ 0.03, which is attributed to the volatilization of sulfur and selenium. Benefiting from the introduced extra electronics by Bi3+ doping, the carrier concentration was optimized in 2.31×1021 cm–3. Multiscale defects introduced by Bi–Se co-doping, including secondary phases, micropores, and point defects (BiCu••, SeS×, and VS••), strongly scattered the phonons, leading to a drastically decreased thermal conductivity from 2.71 W m–1 K–1 for Cu1.8S at 773 K to 0.80 Wm–1 K–1 for Cu1.74Bi0.06S0.91Se0.09. A maximum ZT of 0.78 was achieved for Cu1.74Bi0.06S0.91Se0.09 at 773 K, which is 144% higher than that of Cu1.8S (0.32). The current stress test confirms that Bi doping could improve the stability of Cu1.8S by suppressing the Cu ion migration. Our work demonstrates that Bi–Se co-doping is an effective way to enhance the TE properties for Cu1.8S.The Supporting Information is available free of charge at https://pubs.acs.org/doi/10.1021/acsaem.2c00414.SPB model calculation of our work; method for the current stress test; calculation formulas for ZTeng and ηmax; temperature dependence of thermal properties of the Cu1.8–2xBi2xS1–3xSe3x (x = 0, 0.01, 0.02, 0.25, 0.03) samples; and repeatability test of electrical properties for the Cu1.74Bi0.06S0.91Se0.09 sample (PDF)This article has not yet been cited by other publications.

Thermoelectric Performance Enhancement of Cu2S by Se Doping Leading to a Simultaneous Power Factor Increase and Thermal Conductivity Reduction

Simultaneous Enhancement in the Power Factor and Thermoelectric Performance of Copper Sulfide by In2s3 Doping

Enhanced Thermoelectric Performance of Cu2Se Alloys by Simultaneous Engineering of Thermal and Electrical Transport Properties Through S and Te co‐doping

Enhancing thermoelectric performance of Cu1.8S by Sb/Sn co-doping and incorporating multiscale defects to scatter heat-carrying phonons

Doping-mediated stabilization of copper vacancies to promote thermoelectric properties of Cu2−xS

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu1.8S Via Carrier Concentration Regulation and Multiscale Phonon Scattering

Ultralow Thermal Conductivity and Enhanced Figure of Merit for CuSbSe2 Via Cd-Doping

Realized High Power Factor and Thermoelectric Performance in Cu3SbSe4

Enhancement of the thermoelectric properties of MnSb2Se4 through Cu resonant doping

Ultralow Thermal Conductivity and Enhanced Figure of Merit for CuSbSe 2 via Cd-Doping

Synergetic Modulation of Power Factor and Thermal Conductivity for Cu3SbSe4-based System

Enhanced Thermoelectric Performance of CuSbSe2 Via Mn Doping

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu 1.8 S via Carrier Concentration Regulation and Multiscale Phonon Scattering

Enhancing thermoelectric and mechanical properties of p-type Cu3SbSe4-based materials via embedding nanoscale Sb2Se3

Enhancing the Thermoelectric Performance of Cu2se Via Ag Doping

Enhancement of thermoelectric performance of Cu 1.98 Se by Pb doping

Enhanced Thermoelectric Properties of Cu2SnSe3-Based Materials with Ag2Se Addition

High Thermoelectric Performance of Cu 3 SbSe 4 Obtained by Synergistic Modulation of Power Factor and Thermal Conductivity

Phase Tuning for Enhancing the Thermoelectric Performance of Solution-Synthesized Cu 2– x S

Achieving High Power Factor And Thermoelectric Performance Through Dual Substitution Of Zn And Se In Tetrahedrites Cu12sb4s13

Enhanced Thermoelectric Performance Through Tuning Bonding Energy in Cu2Se1–xSx Liquid-like Materials