Abstract:Cu3SbSe4, featuring its earth-abundant, cheap, nontoxic and environmentally friendly constituent elements, can be considered as a promising intermediate temperature thermoelectric (TE) material. Herein, a series of p-type Bi-doped Cu3Sb1−xBixSe4 (x = 0–0.04) samples were fabricated through melting and hot pressing process, and the effects of isovalent Bi-doping on their TE properties were comparatively investigated by experimental and computational methods. TEM analysis indicates that Bi-doped samples consist of Cu3SbSe4 and Cu2−xSe impurity phases, which is in good agreement with the results of XRD, SEM and XPS. For Bi-doped samples, the reduced electrical resistivity (ρ) caused by the optimized carrier concentrations and enhanced Seebeck coefficient derived from the densities of states near the Fermi level give rise to a high power factor of ~ 1000 µWm−1 K−2 at 673 K for the Cu3Sb0.985Bi0.015Se4 sample. Additionally, the multiscale defects of Cu3SbSe4-based materials involving point defects, nanoprecipitates, amorphous phases and grain boundaries can strongly scatter phonons to depress lattice thermal conductivity (κlat), resulting in a low κlat of ~ 0.53 Wm−1 K−1 and thermal conductivity (κtot) of ~ 0.62 Wm−1 K−1 at 673 K for the Cu3Sb0.98Bi0.02Se4 sample. As a consequence, a maximum ZT value ~ 0.95 at 673 K is obtained for the Cu3Sb0.985Bi0.015Se4 sample, which is ~ 1.9 times higher than that of pristine Cu3SbSe4. This work shows that isovalent heavy element doping is an effective strategy to optimize thermoelectric properties of copper-based chalcogenides.

Enhanced Thermoelectric Performance of Nonstoichiometric Compounds Cu3−x SbSe4 by Cu Deficiencies

Are Cu2Te‐Based Compounds Excellent Thermoelectric Materials?

High Thermoelectric Performance of Cu 3 SbSe 4 Obtained by Synergistic Modulation of Power Factor and Thermal Conductivity

Thermoelectric Performance of Non-Stoichiometric Permingeatite Cu3+mSbSe4

Superior thermoelectric performance in non-stoichiometric Cu 3 SbSe 4 system: towards synergistic optimization of carrier and phonon transport

Enhanced thermoelectric properties of Cu3SbSe4-based materials by synergistic modulation of carrier concentration and phonon scattering

Enhanced Thermoelectric Performance of Cu2Se Alloys by Simultaneous Engineering of Thermal and Electrical Transport Properties Through S and Te co‐doping

Enhanced Thermoelectric Properties of Cu3SbSe4 Compounds by Isovalent Bismuth Doping

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu1.8S Via Carrier Concentration Regulation and Multiscale Phonon Scattering

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu 1.8 S via Carrier Concentration Regulation and Multiscale Phonon Scattering

Enhancement of low-temperature thermoelectric performance via Pb doping in Cu3SbSe4

Enhancing the Thermoelectric Performance of Cu1.8S by Sb/Sn Co-Doping and Incorporating Multiscale Defects to Scatter Heat-Carrying Phonons

Enhanced thermoelectric properties of Cu3SbSe4 via configurational entropy tuning

Realizing the Ultralow Lattice Thermal Conductivity of Cu3SbSe4 Compound via Sulfur Alloying Effect

Remarkable Enhancement in Thermoelectric Performance of BiCuSeO by Cu Deficiencies.

Enhancing thermoelectric and mechanical properties of p-type Cu3SbSe4-based materials via embedding nanoscale Sb2Se3

Ultralow Thermal Conductivity and Enhanced Figure of Merit for CuSbSe 2 via Cd-Doping

Thermoelectric Properties of S and Te-doped Cu2SnSe3 Prepared by Combustion Synthesis

High thermoelectric performance of Cu3SbSe4 nanocrystals with Cu2-xSe in situ inclusions synthesized by a microwave-assisted solvothermal method

Unlocking the Potential of Cu3SbSe3: Ultralow Thermal Conductivity and Enhanced Thermoelectric Performance