Abstract:Isostructural alloying has been regarded as an important approach to boosting thermoelectric performance of narrow gap semiconductors through thermal conductivity reduction. However, it does harm to carrier mobilities as well because of atomic disorders. Here, we extend the alloying concept from "isostructural" to "quasi-isostructural", which means that the two alloying components are no longer strictly isostructural but structurally closely related. As a proof-of-concept, a series of cubic Cu2SnSe3–tetragonal Cu3SbSe4 quasi-isostructural alloys (Cu2+xSn1–xSbxSe3+x) were synthesized, and their thermoelectric transport properties were systematically studied. No significant loss of carrier mobilities was found during quasi-isostructural alloying, probably due to the structural similarity of the two end members as well as the negligible mass contrasts between Sn and Sb. Surprisingly, a remarkable reduction of lattice thermal conductivity from 1.2 W m–1 K–1 for Cu2SnSe3/Cu3SbSe4 to 0.4 W m–1 K–1 for Cu5SnSbSe7 at 673 K was observed, which can hardly be explained from a solid solution perspective. Our X-ray photoelectron spectroscopy analysis unambiguously demonstrate the coexistence of Sn2+ and Sn4+ in the alloying systems, whereas Sn simply exhibits Sn4+ in Cu2SnSe3. We deduce that the minute structural changes of Cu2SnSe3 during quasi-isostructural alloying make Sn discordant, leading to its valence state splitting. The mixed-valence scattering therefore strongly impedes phonon propagation beyond alloying. Altogether, a considerably enhanced ZT ≈ 0.4 is realized in the sample with x = 0.2, which is 150% improvement over the x = 0 sample. By selecting the x = 0.5 sample as a representative, a preliminary doping study was performed but seems unsuccessful because of the varying Sn2+/Sn4+ ratio. We expect higher thermoelectric performance in those quasi-isostructural alloys if their carrier concentration can be fully optimized.The Supporting Information is available free of charge at <a class="ext-link" href="/doi/10.1021/acsaem.1c01155?goto=supporting-info">https://pubs.acs.org/doi/10.1021/acsaem.1c01155</a>.Temperature-dependent heat capacity (Cp), thermal diffusivities (D) and Lorenz number (L) for Cu2+xSn1–xSbxSe3+x (x = 0, 0.2, 0.5, 0.8, and 1.0). The longitudinal (νl) and transverse (νt) acoustic velocities, calculation of average acoustic velocity (vs) (<a class="ext-link" href="/doi/suppl/10.1021/acsaem.1c01155/suppl_file/ae1c01155_si_001.pdf">PDF</a>)This article has not yet been cited by other publications.

Superior thermoelectric performance in non-stoichiometric Cu 3 SbSe 4 system: towards synergistic optimization of carrier and phonon transport

Light Element Doping and Introducing Spin Entropy: an Effective Strategy for Enhancement of Thermoelectric Properties in BiCuSeO.

Enhanced thermoelectric properties of Cu3SbSe4-based materials by synergistic modulation of carrier concentration and phonon scattering

Enhanced Thermoelectric Performance of Nonstoichiometric Compounds Cu3−x SbSe4 by Cu Deficiencies

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu1.8S Via Carrier Concentration Regulation and Multiscale Phonon Scattering

Enhanced Thermoelectric Performance in Polymorphic Heavily Co-doped Cu2SnS3 Through Carrier Compensation by Sb Substitution

Enhanced Thermoelectric Performance of Bi–Se Co-Doped Cu 1.8 S via Carrier Concentration Regulation and Multiscale Phonon Scattering

High Thermoelectric Performance of Cu 3 SbSe 4 Obtained by Synergistic Modulation of Power Factor and Thermal Conductivity

Enhancing thermoelectric performance of Cu1.8S by Sb/Sn co-doping and incorporating multiscale defects to scatter heat-carrying phonons

Synergistically optimized electron and phonon transport in high-performance copper sulfides thermoelectric materials via one-pot modulation

Quasi-isostructural Alloying of Cu 2 SnSe 3 –Cu 3 SbSe 4 toward Higher Thermoelectric Performance

Combination of Carrier Concentration Regulation and High Band Degeneracy for Enhanced Thermoelectric Performance of Cu3SbSe4

Enhanced Thermoelectric Properties of Cu3SbSe4 Compounds by Isovalent Bismuth Doping

Enhancement of the thermoelectric properties of MnSb2Se4 through Cu resonant doping

Realizing the Ultralow Lattice Thermal Conductivity of Cu3SbSe4 Compound via Sulfur Alloying Effect

Unlocking the Potential of Cu3SbSe3: Ultralow Thermal Conductivity and Enhanced Thermoelectric Performance

Enhanced Thermoelectric Performance of Cu2Se Alloys by Simultaneous Engineering of Thermal and Electrical Transport Properties Through S and Te co‐doping

Highly Enhanced Thermoelectric and Mechanical Properties of Bi-Sb-Te Compounds by Carrier Modulation and Microstructure Adjustment

Enhancement of low-temperature thermoelectric performance via Pb doping in Cu3SbSe4

Boosting Thermoelectric Performance of BiCuSeO by Improving Carrier Mobility Through Light Element Doping and Introducing Nanostructures

Raising the Thermoelectric Performance in Pb/In-Codoped BiCuSeO by Alleviating the Contradiction between Carrier Mobility and Lattice Thermal Conductivity