Abstract:To optimise the benefits of the deep-rolling process in the service life context of treated components, the process application must be investigated. In addition to the reduction in surface roughness and near-surface material strengthening, compressive residual stresses are introduced, which are primarily responsible for the increase in service life for components, especially in the case of high-strength steel materials. A numerical parameter sensitivity analysis is performed in order to investigate the introduced residual stresses in detail. For this purpose, a validated deep-rolling simulation model is used, which replicates the deep rolling of a railway axle made of the high-strength steel material 34CrNiMo6. The model is based on an elastic-plastic Chaboche material model parameterised on uniaxial tensile and LCF test results and validated with residual stress measurements. Using this model as a basis, the effect of the main process parameters deep-rolling force, feed rate, friction coefficient, number of overruns, tool geometry, and shaft geometry on the resulting residual stress state are investigated. The results reveal that the deep-rolling force has the most significant influence on the introduced residual stress state and should therefore be highlighted. In the case of applying a deep-rolling force of more than 10 kN, maximum compressive residual stresses of around − 1000 MPa are introduced, and a strong saturating behaviour is shown. Maximum compensating tensile residual stresses of + 100 MPa occur below the surface. The main influence of the deep-rolling force is the effective depth achieved, which is determined by the depth of the zero crossing. This varies from 1 mm with an applied force of 2 kN to more than 3.5 mm with 20 kN. Furthermore, the results are analysed to conclude suggestions for the process's applicability, and a proposal for an optimised deep-rolling treatment is presented. There multiple deep rolling with decreased deep-rolling forces is used to achieve a comparably optimised residual stress state. In summary, with the presented results, a contribution to a deeper understanding of the deep-rolling process can be achieved; the influence of the most important process parameters on the residual stress in-depth profiles is established; an optimisation proposal is presented; and correlations are found. Thus, the base work for further fatigue strength assessments and the optimisation of the deep-rolling process regarding the increase of service is laid.

Computer-Simulation Assessment of the Stress–Strain and Kinematic States of a Titanium Nickelide Billet during Screw Rolling

Assessment of shear strains, kinematic state, and deformation zone in two-high screw rolling processes

Modelling of the Rolling Process of Titanium Alloy Tube Billets in Laboratory Conditions on a RSP 14-40 Rolling Mill

Numerical simulation of cold longitudinal asymmetric rolling process

Experimental testing of a new helical rolling technology

Digital simulation of aluminum alloy slab rolling with low relative reduction

Innovative Methodology for Physical Modelling of Multi-Pass Wire Rod Rolling with the Use of a Variable Strain Scheme

Careful finite element simulations of cold rolling with accurate through-thickness resolution and prediction of residual stress

Engineering estimates of strain and strain rate in helical rolling of balls

Numerical parameter sensitivity analysis of residual stresses induced by deep rolling for a 34CrNiMo6 steel railway axle

Analytical and Finite Element Analysis of the Rolling Force for the Three-Roller Cylindrical Bending Process

An Experimental Study of the Thermal State of a Steel Billet during Hot Rolling

Technological Shells in Rolling Processes of Thin Sheets from Hard-to-Deform Materials

DEVELOPMENT OF THE TECHNOLOGICAL PROCESS OF ROLLING BARS IN THE NEW DESIGN RADIAL SHEAR MILL BY USING PHYSICAL MODELING

Computer-aided and experimental study of temperature effect on the quality indicators of piercing mandrels when rolling steel 50 vessels on a screw-rolling mill 30–80. part 1

Texture evolution and slip mode of a Ti-5.5Mo-7.2Al-4.5Zr-2.6Sn-2.1Cr dual-phase alloy during cold rolling based on multiscale crystal plasticity finite element model

Numerical and experimental study of the taper-rolling process for producing a helical blade from a metal strip

Simulation of Residual Stress of V-Notch Specimen Treated by Ultrasonic Rolling

Interpretation of the strain state during cross-roll rolling of aluminum by means of texture analysis

Modeling material behavior of AA5083 aluminum alloy sheet using biaxial tensile tests and its application in numerical simulation of deep drawing

Numerical Simulation of Multi-Pass Hot Rolling of TA1/Q235B Clad Plates