Abstract:To optimise the benefits of the deep-rolling process in the service life context of treated components, the process application must be investigated. In addition to the reduction in surface roughness and near-surface material strengthening, compressive residual stresses are introduced, which are primarily responsible for the increase in service life for components, especially in the case of high-strength steel materials. A numerical parameter sensitivity analysis is performed in order to investigate the introduced residual stresses in detail. For this purpose, a validated deep-rolling simulation model is used, which replicates the deep rolling of a railway axle made of the high-strength steel material 34CrNiMo6. The model is based on an elastic-plastic Chaboche material model parameterised on uniaxial tensile and LCF test results and validated with residual stress measurements. Using this model as a basis, the effect of the main process parameters deep-rolling force, feed rate, friction coefficient, number of overruns, tool geometry, and shaft geometry on the resulting residual stress state are investigated. The results reveal that the deep-rolling force has the most significant influence on the introduced residual stress state and should therefore be highlighted. In the case of applying a deep-rolling force of more than 10 kN, maximum compressive residual stresses of around − 1000 MPa are introduced, and a strong saturating behaviour is shown. Maximum compensating tensile residual stresses of + 100 MPa occur below the surface. The main influence of the deep-rolling force is the effective depth achieved, which is determined by the depth of the zero crossing. This varies from 1 mm with an applied force of 2 kN to more than 3.5 mm with 20 kN. Furthermore, the results are analysed to conclude suggestions for the process's applicability, and a proposal for an optimised deep-rolling treatment is presented. There multiple deep rolling with decreased deep-rolling forces is used to achieve a comparably optimised residual stress state. In summary, with the presented results, a contribution to a deeper understanding of the deep-rolling process can be achieved; the influence of the most important process parameters on the residual stress in-depth profiles is established; an optimisation proposal is presented; and correlations are found. Thus, the base work for further fatigue strength assessments and the optimisation of the deep-rolling process regarding the increase of service is laid.

Technological Shells in Rolling Processes of Thin Sheets from Hard-to-Deform Materials

Development of Advanced Technologies for the Production of Innovative Materials with a Submicrocrystalline Structure by Methods of Severe Plastic Deformation

Solid Shell Element And Its Application In Roll Forming Simulation

Study on the shape prediction of doubly curved shallow shell in flexible rolling process

Ultimate Strength Evaluation of the Multistage Technological Process of Cold Sheet Stamping Technique for Manufacture of Thin-Walled Vessels

Deep Rolling Techniques: A Comprehensive Review of Process Parameters and Impacts on the Material Properties of Commercial Steels

Analysis and design optimization of double-sided deep cold rolling process of a Ti-6Al-4V blade

Numerical simulation of the process manufacture of large-scale composite shell taking into account thermo viscoelastic

Study on Asymmetric Rolling Process Applied to Aluminum Alloy Sheets

Analytical and Finite Element Analysis of the Rolling Force for the Three-Roller Cylindrical Bending Process

Optimizing the Rolling Process of Lightweight Materials

Research on Plastic Deformation Behavior of Double Rollers Clamping Sheet Metal Spinning Process

Numerical simulation of cold longitudinal asymmetric rolling process

Deformation of Large Curved Shells Using Double-Sided Pressure Sheet Hydroforming Process

Numerical parameter sensitivity analysis of residual stresses induced by deep rolling for a 34CrNiMo6 steel railway axle

Collaborative Improvement of Macro-Deformation and Fatigue Property for Thin-Walled Parts in TA19 Titanium Alloy Via a Double-Sided Simultaneous Ultrasonic Surface Rolling Process

Hot forming of box-shaped material blanks under isothermal conditions

Wrinkling and Strengthening Behaviors in the Two-Layer-Sheet Hot-Forming–Quenching Integrated Process for an Al–Cu–Mg-Alloy Thin-Walled Curved-Surface Shell

Numerical Simulation Research on A New Spinning Process: Double-Roller Clamping Spinning Process

Computer-Simulation Assessment of the Stress–Strain and Kinematic States of a Titanium Nickelide Billet during Screw Rolling

Modelling of the Rolling Process of Titanium Alloy Tube Billets in Laboratory Conditions on a RSP 14-40 Rolling Mill