Abstract:CaMg 2 Bi 2 -based compounds, a kind of the representative compounds of Zintl phases, have uniquely inherent layered structure and hence are considered to be potential thermoelectric materials. Generally, alloying is a traditional and effective way to reduce the lattice thermal conductivity through the mass and strain field fluctuation between host and guest atoms. The cation sites have very few contributions to the band structure around the fermi level; thus, cation substitution may have negligible influence on the electric transport properties. What is more, widespread application of thermoelectric materials not only desires high Z T value but also calls for low-cost and environmentally benign constituent elements. Here, Ba substitution on cation site achieves a sharp reduction in lattice thermal conductivity through enhanced point defects scattering without the obvious sacrifice of high carrier mobility, and thus improves thermoelectric properties. Then, by combining further enhanced phonon scattering caused by isoelectronic substitution of Zn on the Mg site, an extraordinarily low lattice thermal conductivity of 0.51 W m -1 K -1 at 873 K is achieved in (Ca 0.75 Ba 0.25 ) 0.995 Na 0.005 Mg 1.95 Zn 0.05 Bi 1.98 alloy, approaching the amorphous limit. Such maintenance of high mobility and realization of ultralow lattice thermal conductivity synergistically result in broadly improvement of the quality factor β . Finally, a maximum Z T of 1.25 at 873 K and the corresponding Z T a v e up to 0.85 from 300 K to 873 K have been obtained for the same composition, meanwhile possessing temperature independent compatibility factor. To our knowledge, the current Z T a v e exceeds all the reported values in AMg 2 Bi 2 -based compounds so far. Furthermore, the low-cost and environment-friendly characteristic plus excellent thermoelectric performance also make the present Zintl phase CaMg 2 Bi 2 more competitive in practical application.

Enhanced Thermoelectric Performance of LiZnSb-Alloyed CaZn 0.4 Ag 0.2 Sb by Band Engineering

Enhancing thermoelectric performance of AB 2 Sb 2 -type Zintl phase through band shaping and lattice distortion

Realizing high thermoelectric performance in p-type CaZn2Sb2-alloyed Mg3Sb2-based materials via band and point defect engineering

Tuning the Thermoelectric Properties of Ca9zn4+Xsb9 by Controlled Doping on the Interstitial Structure

Enhanced Thermoelectric Performance of Zintl Phase Ca9Zn4+ xSb9 by Beneficial Disorder on the Selective Cationic Site

Band convergence and phonon engineering to optimize the thermoelectric performance of CaCd 2 Sb 2

Alloying-Induced Structural Transition in the Promising Thermoelectric Compound CaAgSb

Na/Bi-co-doping and Heterogeneous Interfaces Leading to Enhanced Thermoelectric Performance of P-Type Mg3Sb2-based Zintls

Promising Zintl-Phase Thermoelectric Compound SrAgSb

Enhanced thermoelectric performance of P-type CaMg2Bi1.98 and optimized CaAl2Si2-type Zintl phase module with equal cross-section area

Achieving High Thermoelectric Performance in Rare-Earth Element-Free CaMg 2 Bi 2 with High Carrier Mobility and Ultralow Lattice Thermal Conductivity

Defect Modulation on CaZn1-xAg1-ySb (0 < X < 1; 0 < Y < 1) Zintl Phases and Enhanced Thermoelectric Properties with High Zt Plateaus

Regulating thermoelectric properties of Eu0.5Ca0.5Zn2Sb2 through Mg dopant

Planar Zintl-phase high-temperature thermoelectric materials XCuSb (X = Ca, Sr, Ba) with low lattice thermal conductivity

Improved Thermoelectric Properties of BiSbTe-AgBiSe 2 Alloys by Suppressing Bipolar Excitation

Breaking the Minimum Limit of Thermal Conductivity of Mg3Sb2 Thermoelectric Mediated by Chemical Alloying Induced Lattice Instability

Thermoelectric performance of (AgBiTe2)1-x(SnTe)x with stable cubic enabled by enhanced configurational entropy

Thermoelectric performance improvement of p-type Mg3Sb2-based materials by Zn and Ag co-doping

Electronic Orbital Alignment and Hierarchical Phonon Scattering Enabling High Thermoelectric Performance p-Type Mg 3 Sb 2 Zintl Compounds

Enhanced Thermoelectric and Mechanical Performances in Sintered Bi 0.48 Sb 1.52 Te 3 –AgSbSe 2 Composite

Optimizing the Dopant and Carrier Concentration of Ca5Al2Sb6 for High Thermoelectric Efficiency