Abstract:Since the formation of fouling reduces heat transfer efficiency and causes energy loss, anti-fouling is desirable and may be achieved by coating. In this work, a nickel-tungsten-phosphorus (Ni-W-P) coating was prepared on the mild steel (1015) substrate using electroless plating by varying sodium tungstate concentration to improve its anti-fouling property. Surface morphology, microstructure, fouling behavior, and heat transfer performance of coatings were further reported. Also, the reaction path, transition state, and energy gradient change of calcite, aragonite, and vaterite were also calculated. During the deposition process, as the W and P elements were solids dissolved in the Ni crystal cell, the content of Ni element was obviously higher than that of the other two elements. Globular morphology was evenly covered on the surface. Consequently, the thermal conductivity of ternary Ni-W-P coating decreases from 8.48 W/m·K to 8.19 W/m·K with the increase of W content. Additionally, it goes up to 8.93 W/m·K with the increase of heat source temperature 343 K. Oxidation products are always accompanied by deposits of calcite-phase CaCO3 fouling. Due to the low surface energy of Ni-W-P coating, Ca2+ and [CO3]2− are prone to cross the transition state with a low energy barrier of 0.10 eV, resulting in the more formation of aragonite-phase CaCO3 fouling on ternary Ni-W-P coating. Nevertheless, because of the interaction of high surface energy and oxidation products on the bare matrix or Ni-W-P coating with superior W content, free Ca2+ and [CO3]2− can be easy to nucleate into calcite. As time goes on, the heat transfer efficiency of material with Ni-W-P coating is superior to the bare surface.

Electroless deposition of ternary Ni–P alloy coatings containing tungsten or nano-scattered alumina composite on steel

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

The Research on Coating of Electroless Ni-W-P Ternary Alloys

Study on Electroless Plating Ni-W-P Ternary Alloy with High Tungsten from Compound Complexant Bath

Preparation and Properties of Textured Ni–W Coatings Electrodeposited on the Steel Surface from a Pyrophosphate Bath

Composite Electroless Nickel-nano Al2O3 Coatings on Steel Substrate

Effects of Cobalt Content on Mechanical and Corrosion Properties of Electroless Ni‐Co‐P/TiN Nanocomposite Coatings

The Evolution of Growth Morphology and Corrosion Behavior of Electrodeposited Ni–P Coatings on Alumina Borate Whisker‐reinforced Pure Aluminum Composite

Fabrication and Performance of Ni-Co-P/Si<sub>3</sub>N<sub>4</sub> Electroplated Composite Coatings on Al-Si Alloys

Electroless deposited ternary alloys: third element chemical state, localisation and influence on the properties. A short review

Parameter Optimization for Electroless Ni–W–P Coating

Study on Heat Transfer Performance and Anti-Fouling Mechanism of Ternary Ni-W-P Coating

Electrodeposition of Ni-W-P alloy

Preparation and characterization of electrodeposited Ni–TiC, Ni–TiN, and Ni–TiC–TiN composite coatings on tungsten carbide cutting tool

The Research on Technology of Electroless Ni-W-P Ternary Alloys Plating on the Aluminium Alloy

A Study of Corrosion Resistance and Formation Characteristics of Electroless Ni–P Alloy Coatings on Al18B4O33w/6061 Al Composite with a Simple Surface Pre-Treatment

Influence of the bath pH value on the microstructure and properties of a novel electrodeposited Ni-W-Ti3C2TX composite coating

Effect of variations in Ni-W molar ratio on the microstructure, mechanical properties and tribology of electrodeposited Ni-W/diamond composite coatings

Preparation and Properties of Ni–Co–P/nano‐sized Si3N4 Electroless Composite Coatings

Electrodeposition of Ni-P composite coatings: A review

Investigation of the Tribological and Mechanical Properties of Electroless Ni-P-hBN Nano-Composite Coating