Abstract:The paper shows the effect of solution temperature on the deposition rate of applying composite nickel-phosphorus coatings modified with boron nitride and polytetrafluoroethylene to powder samples made of improved P40, P40Kh and P40KhN steels obtained by hot stamping of porous sintered blanks. It has been experimentally established that within the range of 70–90 °C, the average deposition rate of modified BN and (C 2 F 4 ) n coatings is 15–19 μm/h, while the chemical composition of the improved steels and the surface configuration of the samples have no effect on the coating build-up rate. The mechanism of the formation of the structure and properties of nickel-phosphorus coatings (NiPC) without additives and those of NiPC modified with boron nitride and polytetrafluoroethylene during deposition, sintering and running-in is revealed. It has been established that immediately after deposition, Ni–P coating has an amorphous structure with inclusions of nickel particles, and its microhardness does not exceed 380–390 MPa with no modifiers added. In the dry friction mode at the running-in stage, Ni 12 P 5 and Ni 2 P phases are formed in the modified Ni–P coatings, allowing to improve their tribological properties, and in the steady-state mode, the phase disordering of the modified NiPC proceeds. It has been experimentally revealed that the coefficient of friction and wear decrease by 1.3 times when only (C 2 F 4 ) n is introduced into Ni–P coating, these indices decrease by 1.6 times when only BN is added, and they decrease almost twice when BN and (C 2 F 4 ) n are introduced together. It has been established that upon the combined (complex) modification of NiPC with BN and (C 2 F 4 ) n after the heat treatment, there is almost no nickel oxide phase, nickel boride of NiB type is formed in the coating during running-in, and its content does not decrease when entering the stationary friction mode, thus increasing tribotechnical properties of the coating. During running-in, the coefficient of friction of Ni–P + BN + (C 2 F 4 ) n coating decreases from 0.28 to 0.19, and the wear rate of such a coating in the stationary friction mode is 1.5 mg/h. The efficiency of applying the antifriction nickel-phosphorus coatings modified with BN + (C 2 F 4 ) n to the products made of the improved structural steels obtained by various methods has been theoretically and experimentally substantiated.

Investigation of the Tribological and Mechanical Properties of Electroless Ni-P-hBN Nano-Composite Coating

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Preparation and Tribological Properties of the Carbon Nanotubes–ni–p Composite Coating

Tribo-corrosion and mechanical performance of electro-deposited nano-composite h-BN/epoxy coating

Tribological Behavior and Surface Analysis of Ni–P/BP Coatings

SYNTHESIS AND THE PERFORMANCE OF CARBON NANOTUBES-(Ni-P) COMPOSITES

Enhancing NiCoB alloy coatings with hBN nanoparticles: exploring structural, mechanical, and corrosion improvements through pulse electrodeposition

Hardness and tribological properties of co-electrodeposited Ni-W-B/B coatings

Composite Electroless Nickel-nano Al2O3 Coatings on Steel Substrate

Electroless Preparation and Tribological Properties of Ni-P-Carbon Nanotube Composite Coatings under Lubricated Condition

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Tribological properties of Ni–P-multi-walled carbon nanotubes electroless composite coating

Effect of Heat‐Treatment and NiB–TiO2 Composite Coating on the Tribological Performance of AISI P20 Steel

Enhanced Mechanical and Tribological Capabilities of a Silicon Aluminum Alloy with an Electroplated Ni–Co–P/Si3N4 Composite Coating

Corrosion and wear resistance behaviors of electroless Ni–Cu–P–TiN composite coating

Effect of modifiers on the structure formation and properties of nickel-phosphorus coatings applied to powder steels

Study on Ni-P-nanoTiN Electroless Composite Coating

Preparation and tribological properties of Ni-P electroless composite coating containing inorganic fullerene-like WS2 nanomaterials

Friction and Wear Behavior of Electroless Wear-Resistant and Self-Lubricating Ni-P Composite Coatings

Tribological Behaviors of Electroless Nickel-Boron Coating on Titanium Alloy Surface

Friction and wear behavior of Ni-P-carbon nanotubes (CNTs) electroless composite coating