Abstract:Abstract Here, numerous oxygen-containing functional groups were grafted onto the surface of CNTs to improve their dispersibility in an electrolyte. The CNTs were characterized by FT-IR, Raman, XPS, FE-SEM, and TEM. The results revealed that the dispersibility of the functionalized CNTs in the composites was better than unfunctionalized CNTs. CNTs/Ni composites were deposited on a copper plate by pulsed electrodeposition and ultrasonic dispersion using an electrolytic bath with CNTs concentrations from 0 to 2 g l −1 . The friction and wear behavior of the composite coatings were assessed using two different methods. In the first method, the coatings were scratched with a progressively higher load from 0–100 N, and the results demonstrate a 10 percent reduction in the coefficient of friction (COF) of the composite compared to pure nickel. The other method involved applying a constant load of 30 N, the COF and microscopic wear mechanism were investigated at different carbon nanotube contents, and the results confirmed that the COF of the composites was gradually reduced with the increase of carbon nanotube mass concentration, and the COF was only 0.343 when the carbon nanotube content was increased to 2 g l −1 . According to the XRD results, increasing the CNTs contents changed the preferred growth orientation. Moreover, the FE-SEM images of the wear surface of the 1 g l −1 CNTs/Ni sample indicated that it had the best wear resistance and showed the smoothest wear trace without apparent cracks. The addition of CNTs enhanced the wear resistance of the nickel matrix due to the superior mechanical strength and lubricating effect of the CNTs. CNTs exposed to the matrix surface reduced the direct contact between the Ni matrix and the friction pair, acted as lubricants, and reduced the wear rate.

Preparation and characterization of electrodeposited Ni–TiC, Ni–TiN, and Ni–TiC–TiN composite coatings on tungsten carbide cutting tool

Structural characterization and adhesion appraisal of TiN and TiCN coatings deposited by CAE-PVD technique on a new carbide composite cutting tool

Development of Al-Ni-TiC Composite Coating on Commercially Pure Al Using Tungsten Inert Gas Welding Route and its Wear Behavior

Comparative analysis over microstructural, mechanical properties and cutting performance of TiN, TiVN coatings deposited by magnetron sputtering on SiAlON ceramic tool insert

Electroless deposition of ternary Ni–P alloy coatings containing tungsten or nano-scattered alumina composite on steel

Electrodeposition of Ni-WC composite coatings: formation, structure and properties

Investigations on microstructure, mechanical and tribological properties of TiN coatings deposited on three different tool materials

Effect of Pulse Electrodeposition Mode on Microstructures and Properties of Ni-TiN Composite Coatings

Effect of Ti Microparticles on the Microstructure and Properties of Ni-Ti Composite Coating Prepared by Electrodeposition

Influence of the bath pH value on the microstructure and properties of a novel electrodeposited Ni-W-Ti3C2TX composite coating

Investigation on Microstructure and Properties of Electrodeposited Ni-Ti-CeO2 Composite Coating

Effect of TiN concentration on microstructure and properties of Ni/W–TiN composites obtained by pulse current electrodeposition

Friction and wear behaviors of electrodeposited Ni-P-CNTs composite coatings on Al-alloy substrate

Adding WC Nano-particles to Nickel-Based Coating Deposited by PTA Process: Microstructure and Nanoindentation Hardness Characteristics

Tailoring role of Al and Ti particles in the microstructure and property of electrodeposited Ni matrix nanocomposite coatings

Nanostructured Ni–WC–Co composite coatings fabricated by electrophoretic deposition

Preparation and Characterization of Nanostructured Ni-TiN Composite Films

Comparative investigation and characterization of the nano-mechanical and tribological behavior of RF magnetron sputtered TiN, CrN, and TiB2 coating on Ti6Al4V alloy

Influence of Ti3C2Tx Addition on the Corrosion Behaviour and Tribological Properties of Electrodeposited Ni-W-Ti3C2Tx Nanocomposite Coatings

Investigation of the microstructure and tribological properties of CNTs/Ni composites prepared by electrodeposition

Microstructure and mechanical properties of electroless Ni–P–Si 3 N 4 –TiN composite coatings