Abstract:In order to achieve desired mechanical properties of alloys by manipulating grain boundaries (GBs) via solute decoration, it is of great significance to understand the underlying mechanisms of microstructural evolution and plastic deformation. In this work, nanocrystalline (NC) Cu-W alloyed films with W concentrations spanning from 0 to 40 at% were prepared by using magnetron sputtering. Thermal stability (within the temperature range of 200 °C-600 °C) and hardness of the films were investigated by using the x-ray diffraction, transmission electron microscope (TEM) and nanoindentation, respectively. The NC pure Cu film exhibited substantial grain growth upon all annealing temperatures. The Cu-W alloyed films, however, displayed distinct microstructural evolution that depended not only on the W concentration but also on the annealing temperature. At a low temperature of 200 °C, all the Cu-W alloyed films were highly stable, with unconspicuous change in grain sizes. At high temperatures of 400 °C and 600 °C, the microstructural evolution was greatly controlled by the W concentrations. The Cu-W films with low W concentration manifested abnormal grain growth (AGG), while the ones with high W concentrations showed phase separation. TEM observations unveiled that the AGG in the Cu-W alloyed thin films was rationalized by GB migration. Nanoindentation results showed that, although the hardness of both the as-deposited and annealed Cu-W alloyed thin films monotonically increased with W concentrations, a transition from annealing hardening to annealing softening was interestingly observed at the critical W addition of ∼25 at%. It was further revealed that an enhanced GB segregation associated with detwinning was responsible for the annealing hardening, while a reduced solid solution hardening for the annealing softening.

Fabrication, thermal stability and microhardness of sputtered Ni–P–W coating

Fabrication and performance of Ni-Co-P/Si3N4 electroplated composite coatings on al-si alloys

Preparation and Properties of Textured Ni–W Coatings Electrodeposited on the Steel Surface from a Pyrophosphate Bath

Mechanical and Tribological Properties of Ni-B and Ni-B-W Coatings Prepared by Electroless Plating

Study on Electroless Plating Ni-W-P Ternary Alloy with High Tungsten from Compound Complexant Bath

Microstructure and wear properties of crystalline W alloy coatings prepared by electrodeposition

Electrodeposition of Ni-W-P alloy

Influence of W content on microstructure and surface morphology of hard Ni-W films fabricated by magnetron co-sputtering

The W alloying effect on thermal stability and hardening of nanostructured Cu-W alloyed thin films

Synthesis, Composition, Morphology, and Wettability of Electroless Ni-Fe-P Coatings with Varying Microstructures

Electroless deposition of ternary Ni–P alloy coatings containing tungsten or nano-scattered alumina composite on steel

Study on Heat Transfer Performance and Anti-Fouling Mechanism of Ternary Ni-W-P Coating

Excellent Properties of Ni-15 wt.% W Alloy Electrodeposited from a Low-Temperature Pyrophosphate System

Investigation of the Enhancement Mechanism of Electrochemically Deposited Ni–Co–W Coatings via Laser Irradiation: Effect of W Contents on Corrosion Resistance

Fabrication and Characterization of Tungsten Heavy Alloys with High W Content by Powder Metallurgy

The Research on Coating of Electroless Ni-W-P Ternary Alloys

Mechanical properties of Ni-based coatings fabricated by electroless plating method

Wear and Corrosion Properties of Crystalline Ni-W Alloy Coatings Prepared by Electrodeposition

The Research on Technology of Electroless Ni-W-P Ternary Alloys Plating on the Aluminium Alloy

Hard and tough nitrogen doped tungsten coatings deposited by HIPAC: Microstructure and mechanical properties

Study on the soft magnetic properties, corrosion, and wear resistance of Ni–Co–W coatings deposited via laser-assisted electrochemical technique: Potential applications in advanced electromagnetic devices