Abstract:The deposition of ternary nitrides with the incorporation of carbon atoms into its structure has demonstrated to be a promising approach in the pursuit of wear-resistant and self-lubricating coatings. Firstly, both TiAlN and TiAlCN monolayers were deposited using direct current magnetron sputtering (DCMS) and high-power impulse magnetron sputtering (HiPIMS) onto quenched and tempered AISI H11 tool steel to be used as references. Acetylene was used as a carbon precursor, producing DCMS and HiPIMS TiAlCN coatings with 9.0 and 21.7 at.% C, respectively.Subsequently, TiAlN/TiAlCN multilayers of various designs were also developed as follows: 5×[10/500], 5×[50/500] and 5×[100/500] nm. Residual stresses of the coating systems were determined by X-ray radiation utilising an ETA-diffractometer with a Cu-Kα radiation source applying the sin2ψ method. Additionally, residual stresses depth gradients of the substrate before and after the deposition of the coatings were determined in a LEDDI 8-circle diffractometer equipped with a W-X-ray tube and operated in the energy-dispersive mode of diffraction. Great reduction of the compressive residual stresses in the coatings was observed after the introduction of carbon into the TiAlN coating structure, shifting from −1047 ± 149 to −307 ± 211 MPa for the DCMS and from −7035 ± 1361 to +989 ± 187 MPa for the HiPIMS coatings. In the multilayer coatings, compressive residual stresses increase along with the increment of the TiAlN interlayer. Additionally, residual stresses of the substrate in the near-surface are dragged from low compressive stresses (−218 ± 61) to tensile stresses in the range of 1000 to 2000 MPa for all the DCMS/substrate systems, a behaviour only presented in HiPIMS by the TiAlN monolayer. Wear coefficients of all the evaluated HiPIMS systems are notoriously lower than their DCMS counterparts. Compared to TiAlN, TiAlCN HiPIMS presented a lower coefficient of friction but a higher wear coefficient, which in turn was not reduced by the introduction of the multilayer systems. Finally, Scratch test and Rockwell C adhesion tests have shown higher adhesion of DCMS coatings than HiPIMS coatings, and a detriment of the monolayers adhesion by the implementation of TiAlN/TiAlCN multilayer systems. The understanding of the residual stresses, both in the coating and in the substrate, and the way they affect the tribomechanical performance of the system coating/substrate continues to be of great importance, especially for coatings deposited by new technologies such as HiPIMS and self-lubricating coatings.

Graded and Single-Layer NiAl/WC-Co Coatings Processed by Plasma Transferred Arc Directed Energy Deposition

Effect of Process Parameters on Microstructure and Properties of AlCoCrFeNi-WC-WS2 Composite Coating Prepared by Laser Cladding

Thermal-induced evolution of microstructure as a plasma arc coating Direction-Dependent phenomenon

The Hardfacing Properties of the Nickel-based Coating Deposited by the PTA Process with the Addition of WC Nano-particles: Wear Investigation

Comparative Study of Multilayer Hard Coatings Deposited on WC-Co Hardmetals

Electroless deposition of ternary Ni–P alloy coatings containing tungsten or nano-scattered alumina composite on steel

Adding WC Nano-particles to Nickel-Based Coating Deposited by PTA Process: Microstructure and Nanoindentation Hardness Characteristics

Residual stresses and tribomechanical behaviour of TiAlN and TiAlCN monolayer and multilayer coatings by DCMS and HiPIMS

Tribological Investigation of W-Ti-N Thin Film on Plasma Nitrided Stainless-Steel Multilayer Coating

Microstructure and Tribological Properties of Laser-Remelted Ni-Based WC Coatings Obtained by Plasma Spraying

Microstructure Evaluation and High-Temperature Wear Performance of Hard Protective Layer Deposited on Titanium Alloy via Laser Metal Deposition

The Microstructure and Properties of Ni60/60% WC Wear-Resistant Coatings Prepared by Laser-Directed Energy Deposition

Deposition of NiAl/Al3Ni2(CrB2) Coatings from Ni, Al and CrB2 Powders Using Mechanical Synthesis in Planetary Ball Mill

Microstructure and wear behavior of WC-reinforced AlCoCrFeNiSi high entropy alloy coatings prepared by high-velocity arc spraying

Nanoindentation and Tribological Behavior of TiN-TiCN-TiAlN Multilayer Coatings on AISI D3 Tool Steel

Effect of Scanning Strategy on the Microstructure and Triboperformance of FeNiCrMo Coating Manufactured by Plasma Transferred Arc

Thermal Fatigue Resistance Studies of Multilayer CrN and AlTiN Coatings Deposited on Plasma Nitrided H-13 Hot Work Steel

Microstructure, Mechanical and Adhesive Properties of CrN/CrTiAlSiN/WCrTiAlN Multilayer Coatings Deposited on Nitrided AISI 4140 Steel

Mechanical, Tribological, and Electrochemical Evaluation of NiCrAlMoFe Thermally Sprayed Coatings Subject to Post-treatments

Laser Surface Modification of TC21 (α/β) Titanium Alloy Using a Direct Energy Deposition (DED) Process