Abstract:The results of corrosion-fatigue studies on the D16T aluminum alloy after its protection by different methods are presented. The effects of cathodic polarization, surface-plastic deformation, zinc and nickel electroplating, and corrosion inhibitor on its fatigue and corrosion-fatigue characteristics are investigated. It is established that shot blasting and rolling (surface treatment by rollers) increase the fatigue limit of duralumin in the air almost equally and by ~20 and ~50% in a 3% NaCl solution, respectively. Such difference in the material's fatigue limits in chlorine-containing medium is due to the higher electrochemical heterogeneity and roughness of the surface after blasting and the different nature of its dissolution. The maximum increase in corrosion endurance of the alloy under cathodic polarization is observed beyond the electrode potential of -1200 mV. At the same time, an increase in the corrosion-fatigue limit by ~50% compared to the unprotected material was recorded. To improve the fatigue characteristics of the alloy in the air and chloride-containing environment with zinc or nickel electroplating, it is necessary to carry out preliminary surface-plastic deformation of the material. The porous nickel coating significantly increased the corrosion resistance of the unloaded alloy in a 3% solution of NaCl but reduced the fatigue limit in the air and chlorine-containing medium by ~2.5 times, due to generated tensile stresses. Zinc coating significantly reduced the dissolution rate of duralumin in a 3% NaCl solution. In addition, it is established that the coating on the ground surface of the alloy insignificantly lowers the fatigue limit, but increases it by 25–30% in the corrosive environment due to its protective action. The strontium chromate effect on the corrosion-fatigue strength of D16T alloy was studied, and its addition in the amount of 0.6 g/L significantly increased the resistance to corrosion-fatigue failure of duralumin alloy in synthetic acid rain.

Performance of dodecyl dimethyl benzyl ammonium chloride as bactericide and corrosion inhibitor for 7B04 aluminum alloy in an aircraft fuel system

Excellent performance of dodecyl dimethyl betaine and calcium gluconate as hybrid corrosion inhibitors for Al alloy in alkaline solution

Investigating the corrosion inhibition of aluminium by diamine derivatives in hydrochloric acid: a multi-technique approach

Corrosion Inhibition Of Q235 Steel By Octyl Dimethyl Benzyl Quaternary Ammonium Salt Ionic Liquid

Anode Interfacial Layer Construction Via Hybrid Inhibitors for High-Performance Al-Air Batteries.

Corrosion inhibition of AA2024-T3 in alkaline solution by disodium-N-dodecyliminodiacetate: Experimental and theoretical studies

Corrosion inhibition performance of synergistic inhibitors on Q235 steel in methanol/formic acid medium

Corrosion inhibition, long-term and adsorption mechanisms of humic acid on ADC12 aluminum alloy in oxalic acid solution

Sodium dodecylbenzene sulfonate film absorbed on magnesium alloy surface: An electrochemical, SKPFM, and molecular dynamics study

Influence of sodium alginate and chromate on aluminum corrosion in simulated HVDC cooling water

Inhibitive effect of anionic/ zwitterionic hybrid surfactants on the self-corrosion of anode for alkaline Al-air battery

Bis(2-hydroxyethyl) ammonium dodecanoate and its constituents as inhibitors for Al corrosion and H2 production in acid medium

Efficiency of Protection Methods Against Corrosion-Fatigue Damage of D16T Aluminum Alloy

Adsorption and Corrosion Inhibition Behavior of Sodium Dodecylbenzenesulfonate on AZ31 Magnesium Alloy

d-tyrosine enhances disoctyl dimethyl ammonium chloride on alleviating SRB corrosion

Synergistic effect of an organic hydrophobic film deposited on MAO containing NaH 2 PO 4 for enhanced corrosion resistance of 6063 aluminum alloy

Sodium dodecyl sulfate (SDS) as an effective corrosion inhibitor for Mg-8Li-3Al alloy in aqueous NaCl: A combined experimental and theoretical investigation

Inhibitive performance of dapoxetine drug for corrosion of aluminum alloy (AA6063) in acidic and alkaline solutions: experimental and theoretical studies using Materials Studio v7.0

Morphological effects on the electrochemical dissolution behavior of forged and additive manufactured Ti-6Al-4V alloys in runway deicing fluid

Ocimum Basilicum Seeds as a New Natural Corrosion Inhibitor for AA7075-T6 Aluminum Alloy in Nacl Solution: Electrochemical, Thermodynamic, Surface, and Theoretical Studies

Detailedexperimental and computational explorations of two heterocyclic compounds as corrosion inhibitors for aluminum alloy 2024-T3 in 3.5% NaCl: Electrochemical/surface studies, DFT/MD modeling