Abstract:Cold-drawn pearlitic steel wires have the highest strength of all steel products. It is a promising way to enhance the mechanical properties by increasing the carbon content. However, the proeutectoid cementite forms easily due to the hypereutectoid composition and deteriorates the mechanical and processing properties of steel wires. It is important for hypereutectoid steel wire drawing to achieve a fine and fully pearlitic microstructure without proeutectoid cementite. The austenitization and following continuous cooling process were simulated in the dilatometer for a hypereutectoid steel. The microstructure was observed with OM and SEM. The transformation temperature, prior-austenite grain size, pearlitic interlamellar spacing and proeutectoid cementite thickness were determined by dilatometric curves or OM/SEM images. The austenite grain size increases rapidly with a higher temperature and almost keeps invariant with a longer austenitization time. Faster cooling rate, higher austenitization temperature or longer austenitization time decrease the starting and finishing temperature of phase transformation, widen the temperature range, refine the pearlitic interlamellar spacing and suppress the proeutectoid cementite precipitation (reduce the thickness or make it discontinuous). However, it is easy to form martensite which is bad for the homogeneity of pearlitic microstructure by increasing the cooling rate or austenitization temperature simply. A fine pearlite in a pseudoeutectoid microstructure is achieved by extending the austenitization time to 60 min and controlling the austenitization temperature and cooling rate. Discontinuous proeutectoid cementite is observed in the samples with the higher austenitization temperature. Higher austenitization temperature and longer time are helpful to weaken the carbon concentration gradient. The homogeneous carbon distribution restrains carbon diffusion for cementite nucleation during the proeutectoid cementite precipitation and pearlite transformation, which decreases the transformation temperature. Compare to pearlite transformation, the proeutectoid cementite precipitation is affected more strongly by the carbon diffusion due to a longer diffusion distance. Therefore, the precipitation amount of proeutectoid cementite is reduced if the carbon diffusion is restrained. The amount of grain corner and grain edge reduce more dramatically than that of grain boundary if austenite grain size increases. The proeutectoid cementite only nucleates in grain corner and grain edge. The pearlite nucleation can form in grain boundary. Therefore, the larger austenite grains result in the sharp reduction in the sites for nucleation of proeutectoid cementite. Then, the amount of proeutectoid cementite are reduced and the morphology becomes discontinuous.

Effect of austenitizing temperature and holding time on austenite grain size of EQ70 steel

Austenite Grain Growth and its Equation in the Austenitizing Process for 700 MPa Grade High-Strength Steel

The Influence of Temperature on the Austenite Grain Size and Microstructure of 4140 Steel

Effect of Cooling Rate after Isothermal Stage of Vacuum Austempering on Microstructure and Hardness of M50 Bearing Steel

DICTRA Simulation of Holding Time Dependence of NbC Size and Experimental Study of Effect of NbC on Austenite Grain Growth

Effect of billet microstructure and deformation on austenite grain growth in forging heating of a medium-carbon microalloyed steel

Study on Austenite Grain Growth Behavior of GCr15 Bearing Steel

Effects of Austenitizing Conditions on the Microstructure of AISI M42 High-Speed Steel

Effect of Austenite Grain Coarsening on Rheological Behavior of Low-carbon High-strength Steel at High Temperature

Effect of cooling rate on microstructure and mechanical properties of a low-carbon low-alloy steel

Effects of Austenitizing Temperature on Microstructure Evolution and Corrosion Resistance of High Cr Ferritic/Martensitic Steel

Influence of Austenitizing Temperature on the Microstructure and Mechanical Properties of an Fe-Cr-Ni-Mo-Ti Maraging Stainless Steel

Effect of austenitizing temperature on variant selection of martensite transformation in a 2 GPa grade steel

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

Effect of Austenitising Temperature on Microstructure and Mechanical Properties of 30si2crni4monb Ultrahigh Strength Steel

Austenite Grain Growth Behavior of A Gcr15 Bearing Steel Cast Billet in the Homogenization Heat Treatment Process

Effect of austempering temperature on microstructure and cyclic deformation behaviour of multiphase low-carbon steel

Effect of the Normalizing Temperature on the Size and Homogeneity of Austenite Grain in 20CrMnTi Carburized Gear Steel

Unraveling the Effects of Austenitizing Temperature and Austenite Grain Size on the Crystallographic Characteristics and Mechanical Properties of Martensitic Transformation Products in a Low-Alloy Steel

Effects of austenitization and cooling rates on the microstructure in a hypereutectoid steel

The effect of austenitizing temperature on the microstructure and mechanical properties of as-quenched 4340 steel