Abstract:The heat transfer model for steel solidification in Al 2 O 3 crucial and permanent mold by finite element method was developed and validated by temperature measurement. The multi-gradient operation was novelly designed, and the tailored cooling rate in range of 0.1–10 °C/s was obtained at the target location. The simulation aided experiment with the large-sized samples was carried out, and the local cooling rate was verified by secondary dendrite arm spacing. The size of austenite grain decreases slightly as cooling rate increases from 0.15 °C/s to 0.31 °C/s, and then increases dramatically in the range of 0.31–0.48 °C/s, finally decreases with cooling rate increasing further to 9.76 °C/s. The relationship between austenite grain size and cooling rate was logarithmically regressed in the range of 0.48–9.76 °C/s, in which the kinetic equations on basis of cooling experiment and continuously cast slab can also work. However, the grain size decrease in 0.15–0.31 °C/s and then increase in 0.31–0.48 °C/s cannot be described. Based on the mechanism of peritectic solidification, the austenite grain growth is mainly controlled by diffusion at a low cooling rate smaller than 0.31 °C/s, and the final grain size is less than 1.0 mm. At a medium cooling rate between 0.48 and 3.60 °C/s, austenite grain growth is accelerated by the energy stored during massive type peritectic transformation previously, and the grain size is between 1.7 and 2.9 mm. At high cooling rate larger than 9.76 °C/s, austenite grains grow to about 0.9 mm in columnar shape. The time for grain growth is not adequate, although addition energy storage by massive transformation can also occur. The critical cooling rate for the onset of massive type peritectic transformation in the large-sized sample is between 0.31 and 0.48 °C/s. The growth velocity in the isothermal experiment is much smaller than that in continuous cooling process, confirming that the austenite grain evolution is significantly affected by previous peritectic solidification.

Austenite Grain Growth and its Equation in the Austenitizing Process for 700 MPa Grade High-Strength Steel

Austenite grain growth in tailored cooling rate experiment designed by numerical simulation for peritectic steel

Austenite Growth Behavior and Prediction Modeling of Ti Microalloyed Steel

The Influence of Temperature on the Austenite Grain Size and Microstructure of 4140 Steel

Austenite Grain Growth Behavior of A Gcr15 Bearing Steel Cast Billet in the Homogenization Heat Treatment Process

Effect of Austenite Grain Size on the Bainitic Transformation in a 690 MPa Grade High-Strength Multi-Functional Construction Steel

Effect of Austenite Grain Coarsening on Rheological Behavior of Low-carbon High-strength Steel at High Temperature

Effects of Austenitizing Conditions on the Microstructure of AISI M42 High-Speed Steel

In Situ Observation of the Grain Growth Behavior and Martensitic Transformation of Supercooled Austenite in NM500 Wear-Resistant Steel at Different Quenching Temperatures

Effect of austenitizing temperature and holding time on austenite grain size of EQ70 steel

Synergistic effect of well/over-tempered hierarchical martensitic structure and carbides (M 23 C 6 and MX) on austenite growth in 9Cr steel

Microstructure evolution and strengthening mechanism of air-hardening steel subjected to the austenitizing annealing treatment

Influence of Austenitisation Time and Temperature on Grain Size and Martensite Start of 51CrV4 Spring Steel

Effect of Austenitizing Temperature on Pearlite Transformation of a Medium-Carbon Steel

Kinetic Transitions and Mn Partitioning During Austenite Growth from a Mixture of Partitioned Cementite and Ferrite: Role of Heating Rate

Effect of austenitizing temperature on variant selection of martensite transformation in a 2 GPa grade steel

Study on Austenite Grain Growth Behavior of GCr15 Bearing Steel

Kinetics of austenite growth and bainite transformation during reheating and cooling treatments of high strength microalloyed steel produced by sub-rapid solidification

Grain growth behaviors during solution annealing based on the heterogeneous microstructure in hot rolled nuclear grade austenitic stainless steel

Carbide dissolution and austenite grain growth behavior of a new ultrahigh-strength stainless steel

Effect of Austenitising Temperature on Microstructure and Mechanical Properties of 30si2crni4monb Ultrahigh Strength Steel