Abstract:Cold-drawn pearlitic steel wires have the highest strength of all steel products. It is a promising way to enhance the mechanical properties by increasing the carbon content. However, the proeutectoid cementite forms easily due to the hypereutectoid composition and deteriorates the mechanical and processing properties of steel wires. It is important for hypereutectoid steel wire drawing to achieve a fine and fully pearlitic microstructure without proeutectoid cementite. The austenitization and following continuous cooling process were simulated in the dilatometer for a hypereutectoid steel. The microstructure was observed with OM and SEM. The transformation temperature, prior-austenite grain size, pearlitic interlamellar spacing and proeutectoid cementite thickness were determined by dilatometric curves or OM/SEM images. The austenite grain size increases rapidly with a higher temperature and almost keeps invariant with a longer austenitization time. Faster cooling rate, higher austenitization temperature or longer austenitization time decrease the starting and finishing temperature of phase transformation, widen the temperature range, refine the pearlitic interlamellar spacing and suppress the proeutectoid cementite precipitation (reduce the thickness or make it discontinuous). However, it is easy to form martensite which is bad for the homogeneity of pearlitic microstructure by increasing the cooling rate or austenitization temperature simply. A fine pearlite in a pseudoeutectoid microstructure is achieved by extending the austenitization time to 60 min and controlling the austenitization temperature and cooling rate. Discontinuous proeutectoid cementite is observed in the samples with the higher austenitization temperature. Higher austenitization temperature and longer time are helpful to weaken the carbon concentration gradient. The homogeneous carbon distribution restrains carbon diffusion for cementite nucleation during the proeutectoid cementite precipitation and pearlite transformation, which decreases the transformation temperature. Compare to pearlite transformation, the proeutectoid cementite precipitation is affected more strongly by the carbon diffusion due to a longer diffusion distance. Therefore, the precipitation amount of proeutectoid cementite is reduced if the carbon diffusion is restrained. The amount of grain corner and grain edge reduce more dramatically than that of grain boundary if austenite grain size increases. The proeutectoid cementite only nucleates in grain corner and grain edge. The pearlite nucleation can form in grain boundary. Therefore, the larger austenite grains result in the sharp reduction in the sites for nucleation of proeutectoid cementite. Then, the amount of proeutectoid cementite are reduced and the morphology becomes discontinuous.

Effect of Austenitizing Temperature on Pearlite Transformation of a Medium-Carbon Steel

Effect of Warm-Rolled Pearlite Microstructural Features on Austenitic Transformation

Unraveling the Effects of Austenitizing Temperature and Austenite Grain Size on the Crystallographic Characteristics and Mechanical Properties of Martensitic Transformation Products in a Low-Alloy Steel

Ultra-Fine Bainite in Medium-Carbon High-Silicon Bainitic Steel

Effect of Austenite Grain Size on the Bainitic Transformation in a 690 MPa Grade High-Strength Multi-Functional Construction Steel

Effect of Ausforming Temperature on Bainite Transformation of High Carbon Low Alloy Steel

Effects of austempering temperature on bainitic microstructure and mechanical properties of a high-C high-Si steel

Effect of Prior Austenite Grain Size on Isothermal Bainite Transformation in 65cr Steel

Bainite Kinetic Transformation of Austempered AISI 6150 Steel

Effects of austenitization and cooling rates on the microstructure in a hypereutectoid steel

Bainite Transformation-Kinetics-Microstructure Characterization of Austempered 4140 Steel

Effect of Prior Austenite Grain Size on Austenite Reversion, Bainite Transformation and Mechanical Properties of Fe-2Mn-0.2C Steel

Effect of Austenite Grain Coarsening on Rheological Behavior of Low-carbon High-strength Steel at High Temperature

Understanding the Effect of Austempering Temperature on the Crystallographic Features and Mechanical Properties of Low-Carbon Bainitic Steel

Effects of Austenitizing Temperature on Microstructure and Mechanical Property of a 4-Gpa-grade PM High-Speed Steel

EFFECT OF AUSTENITE GRAIN SIZE ON STRAIN ENHANCED TRANSFORMATION IN A LOW CARBON STEEL

Effect of austenitizing temperature on variant selection of martensite transformation in a 2 GPa grade steel

Progress in Effect of Alloying Element Partition on Thermodynamics and Kinetics of Pearlite Transformation and Its Austenitization

Evolution of ultrafine bainite microstructure during rapid heating process and the role of retained austenite

Effect of Austenite Grain Size on Phase Transformation Structure of Low‐Carbon Microalloyed Steel

Effect of Austenitizing Temperature and Retained Austenite on Mechanical Properties of 2200MPa Grade Ultra-High Strength Steels