Abstract:The heat transfer model for steel solidification in Al 2 O 3 crucial and permanent mold by finite element method was developed and validated by temperature measurement. The multi-gradient operation was novelly designed, and the tailored cooling rate in range of 0.1–10 °C/s was obtained at the target location. The simulation aided experiment with the large-sized samples was carried out, and the local cooling rate was verified by secondary dendrite arm spacing. The size of austenite grain decreases slightly as cooling rate increases from 0.15 °C/s to 0.31 °C/s, and then increases dramatically in the range of 0.31–0.48 °C/s, finally decreases with cooling rate increasing further to 9.76 °C/s. The relationship between austenite grain size and cooling rate was logarithmically regressed in the range of 0.48–9.76 °C/s, in which the kinetic equations on basis of cooling experiment and continuously cast slab can also work. However, the grain size decrease in 0.15–0.31 °C/s and then increase in 0.31–0.48 °C/s cannot be described. Based on the mechanism of peritectic solidification, the austenite grain growth is mainly controlled by diffusion at a low cooling rate smaller than 0.31 °C/s, and the final grain size is less than 1.0 mm. At a medium cooling rate between 0.48 and 3.60 °C/s, austenite grain growth is accelerated by the energy stored during massive type peritectic transformation previously, and the grain size is between 1.7 and 2.9 mm. At high cooling rate larger than 9.76 °C/s, austenite grains grow to about 0.9 mm in columnar shape. The time for grain growth is not adequate, although addition energy storage by massive transformation can also occur. The critical cooling rate for the onset of massive type peritectic transformation in the large-sized sample is between 0.31 and 0.48 °C/s. The growth velocity in the isothermal experiment is much smaller than that in continuous cooling process, confirming that the austenite grain evolution is significantly affected by previous peritectic solidification.

Kinetics of austenite growth and bainite transformation during reheating and cooling treatments of high strength microalloyed steel produced by sub-rapid solidification

Bainite Transformation-Kinetics-Microstructure Characterization of Austempered 4140 Steel

Kinetic Transitions and Mn Partitioning During Austenite Growth from a Mixture of Partitioned Cementite and Ferrite: Role of Heating Rate

Effect of Rapid Heating and Quenching on Microstructure and Mechanical Properties of High Strength Low Alloy Steel

Study of the kinetics of austenite grain growth by dynamic Ti-rich and Nb-rich carbonitride dissolution in HSLA steel: In-situ observation and modeling

Roles of cooling rate of undercooled austenite on isothermal transformation kinetics, microstructure, and impact toughness of bainitic steel

Investigation of microstructural evolution and bainite transformation kinetics of multi-phase steel

Effect of Austenite Grain Size on Phase Transformation Structure of Low‐Carbon Microalloyed Steel

Low-Carbon Bainite Steel with High Strength and Toughness Processed by Recrystallization Controlled Rolling and Ultra Fast Cooling (RCR+UFC)

Insight into the induction hardening behavior of a new 0.40% C microalloyed steel: Effects of initial microstructure and thermal cycles

Microstructure and Properties of a Low Carbon Bainitic Steel Produced by Conventional and Inverted Two-Step Austempering Processes

Austenite grain growth in tailored cooling rate experiment designed by numerical simulation for peritectic steel

Austenite Formation and Cementite Dissolution During Intercritical Annealing of a Medium-Manganese Steel from a Martensitic Condition

Kinetics of Martensite/Austenite Decomposition during Tempering of Ultrafine Nano-Bainitic Steels

Modeling of the Austenitization of Ultra-high Strength Steel with Cellular Automation Method

Three-dimensional morphology and crystallographic characteristics of the low-temperature bainitic microstructure in high-carbon steel

Austenite Growth Behavior and Prediction Modeling of Ti Microalloyed Steel

Austenite Grain Growth Behavior of A Gcr15 Bearing Steel Cast Billet in the Homogenization Heat Treatment Process

Shaping Microstructure and Mechanical Properties of High-Carbon Bainitic Steel in Hot-Rolling and Long-Term Low-Temperature Annealing

Effect of Austenite Grain Size on the Bainitic Transformation in a 690 MPa Grade High-Strength Multi-Functional Construction Steel