Abstract:Megapores with spherical-like cells connected through windows and high porosities make up catalyst supports in the form of ceramic foams. These characteristics provide significant benefits for catalytic processes that are limited by mass or heat transport. This study focuses on the manufacture of ceramic foam using a polymeric sponge replica process and polymer foams as a template for catalyst supports, which are industrial waste from the packaging sector. To make ceramic foam catalysts, they were dipped in a catalyst solution, followed by a breakdown stage and a sintering process. Experiments focused on determinants that affect the desired characteristics of ceramic foams, such as the types of polymer foams that affect foam morphology, the rheology of catalyst solution that affects catalyst dispersion, and the polymer decomposition rate that affects catalytic performance during dry reforming of the methane process. The cell architectures of polyurethane and polyvinyl alcohol foams are attractive for catalyst support preparation because they have 98-99% porosity and typical cell sizes of 200 and 50 μm, respectively. The polyurethane performance was superior to the performance of polyvinyl alcohol in terms of higher porosity and better catalytic-solution absorption offering high catalyst active areas. The catalyst prepared from concentrated 10 wt % Ni/Al2O3-MgO (10NAM) slurry had the highest surface area (59.18 m2/g) and the highest metal oxide dispersion (5.65%). These results are relevant to the flow behavior of catalyst slurry which plays a key role in coating the catalyst gel on the polymer template. The thermal decomposition rate used to remove the polymer template from the catalyst structure is proportional to the ceramic foam structure (catalyst support structure). The slow decomposition rate bent and fractured foam-cell struts more than the faster rate. On the other hand, achieving good catalyst dispersion on catalyst supports necessitated a high sintering rate. When sintering was adjusted at a high sintering rate, the metal-particle dispersion was relatively high, around 7.44%, and the surface area of ceramic foam catalysts was 64.61 m2/g. Finally, the catalytic behavior toward hydrogen production through the dry reforming of methane using a fixed-bed reactor was evaluated under certain operating conditions.

Preparation of γ-Al2O3/α-Al2O3 ceramic foams as catalyst carriers via the replica technique

Fabrication of a Ceramic Foam Catalyst Using Polymer Foam Scrap via the Replica Technique for Dry Reforming

Factors affecting the microstructure of a fine ceramic foam

Tailoring of the Wetting Behavior of Alumina Dispersions on Polymer Foams by Methylcellulose Addition: A Route Toward Mechanically Stable Ceramic Replica Foams

Development of Centrifugal Coating Device to Load CuZnZr/γ-Al2O3 Catalyst on Porous Substrates for Methanol Steam Reforming

Immobilization of Lipase on Nano- and Microporous Ceramic Foam

Fabrication of γ-Al2O3 Nanoarrays on Aluminum Foam Assisted by Hydroxide for Monolith Catalysts

Design and Formulation of Polyurethane Foam Used for Porous Alumina Ceramics

Reticulated Replica Ceramic Foams: Processing, Functionalization, and Characterization

Preparation and performance analysis of integrated electric heating hydrogen production foam catalyst

ZSM-5@ceramic foam composite catalyst derived from spent bleaching clay for continuous pyrolysis of waste oil to produce monocyclic aromatic hydrocarbons

Regulation Mechanism of the Specific Surface Area of Alumina Ceramic Carriers with Hierarchical Porosity Fabricated by Powder Bed Fusion

Porous reticular CuO/ZnO/CeO2/ZrO2 catalyst derived from polyacrylic acid hydrogel system on Al2O3 foam ceramic support for methanol steam reforming microreactor

Preparation of Ag foam catalyst based on in-situ thermally induced redox reaction between polyvinyl alcohol and silver nitrate with supercritical CO2 foaming technology

Hierarchically Porous Alumina Ceramic Catalyst Carrier Prepared by Powder Bed Fusion

Development of a centrifugal coating method to load catalyst washcoat onto porous substrates with high uniformity and adhesive strength

Highly Porous and Hierarchical MgAl2O4 Ceramics with Improved Pore Connectivity Prepared from Gelled Particle-Stabilized Foams

Design of Induction Heatable Carbon‐Based Foams for Catalysis

Development of centrifugal coating device to load CuZnZr/γ-Al 2 O 3 catalyst on porous substrates for methanol steam reforming

Foamy ceramic filters and new possibilities of their applications

The Preparation and Modification of Active Alumina