Abstract:Megapores with spherical-like cells connected through windows and high porosities make up catalyst supports in the form of ceramic foams. These characteristics provide significant benefits for catalytic processes that are limited by mass or heat transport. This study focuses on the manufacture of ceramic foam using a polymeric sponge replica process and polymer foams as a template for catalyst supports, which are industrial waste from the packaging sector. To make ceramic foam catalysts, they were dipped in a catalyst solution, followed by a breakdown stage and a sintering process. Experiments focused on determinants that affect the desired characteristics of ceramic foams, such as the types of polymer foams that affect foam morphology, the rheology of catalyst solution that affects catalyst dispersion, and the polymer decomposition rate that affects catalytic performance during dry reforming of the methane process. The cell architectures of polyurethane and polyvinyl alcohol foams are attractive for catalyst support preparation because they have 98-99% porosity and typical cell sizes of 200 and 50 μm, respectively. The polyurethane performance was superior to the performance of polyvinyl alcohol in terms of higher porosity and better catalytic-solution absorption offering high catalyst active areas. The catalyst prepared from concentrated 10 wt % Ni/Al2O3-MgO (10NAM) slurry had the highest surface area (59.18 m2/g) and the highest metal oxide dispersion (5.65%). These results are relevant to the flow behavior of catalyst slurry which plays a key role in coating the catalyst gel on the polymer template. The thermal decomposition rate used to remove the polymer template from the catalyst structure is proportional to the ceramic foam structure (catalyst support structure). The slow decomposition rate bent and fractured foam-cell struts more than the faster rate. On the other hand, achieving good catalyst dispersion on catalyst supports necessitated a high sintering rate. When sintering was adjusted at a high sintering rate, the metal-particle dispersion was relatively high, around 7.44%, and the surface area of ceramic foam catalysts was 64.61 m2/g. Finally, the catalytic behavior toward hydrogen production through the dry reforming of methane using a fixed-bed reactor was evaluated under certain operating conditions.

Tailoring of the Wetting Behavior of Alumina Dispersions on Polymer Foams by Methylcellulose Addition: A Route Toward Mechanically Stable Ceramic Replica Foams

Factors affecting the microstructure of a fine ceramic foam

Microstructure of Ceramic Foams

Improvement of Microstructural Controllability of Cellular Ceramic for Multifunctional Composites

Cost-effective Fabrication of Bio-Inspired Nacre-Like Composite Materials with High Strength and Toughness

Design and Formulation of Polyurethane Foam Used for Porous Alumina Ceramics

Preparation of γ-Al2O3/α-Al2O3 ceramic foams as catalyst carriers via the replica technique

High-strength porous alumina ceramics prepared from stable wet foams

Strength Enhancement of Ultralight Alumina‐dried Foams from Particle‐stabilized Foams with Assistance of Agar and PVA

Preparation and Properties of Alumina Ceramic Foams Prepared with Cetyl Sodium Sulfate

Fabrication of a Ceramic Foam Catalyst Using Polymer Foam Scrap via the Replica Technique for Dry Reforming

3D Printable Ultra‐Highly Porous and Mechanically Strong Foam Materials for Multiple Applications

Ultralight Alumina Ceramic Foams with Single-Grain Wall Using Sodium Dodecyl Sulfate As Long-Chain Surfactant

Ultralight and High-Strength Bulk Alumina/zirconia Composite Ceramic Foams Through Direct Foaming Method

Improved energy absorption capacity of Al/Al 2 O 3 foams by the ductile/brittle hybrid deformation mode

Highly Porous and Mechanically Robust Al2O3-based Foams with Self-Wrinkled and Rough Aperture Surfaces Via Binary Colloidal Self-Assembly of Nanoparticle/gelation Network

Ultra-high Porosity of Open-Cell Alumina Ceramic Foams Prepared by Adding Tiny Amounts of Γ-Alo(oh) Sol

Foam-gelcasting preparation and properties of high-strength mullite porous ceramics

Reticulated Replica Ceramic Foams: Processing, Functionalization, and Characterization

Highly Porous Alumina Cellular Ceramics Bonded by In-Situ Formed Mullite Prepared by Gelation-Assisted Al2O3–Si Particle-Stabilized Foams