Abstract:Megapores with spherical-like cells connected through windows and high porosities make up catalyst supports in the form of ceramic foams. These characteristics provide significant benefits for catalytic processes that are limited by mass or heat transport. This study focuses on the manufacture of ceramic foam using a polymeric sponge replica process and polymer foams as a template for catalyst supports, which are industrial waste from the packaging sector. To make ceramic foam catalysts, they were dipped in a catalyst solution, followed by a breakdown stage and a sintering process. Experiments focused on determinants that affect the desired characteristics of ceramic foams, such as the types of polymer foams that affect foam morphology, the rheology of catalyst solution that affects catalyst dispersion, and the polymer decomposition rate that affects catalytic performance during dry reforming of the methane process. The cell architectures of polyurethane and polyvinyl alcohol foams are attractive for catalyst support preparation because they have 98-99% porosity and typical cell sizes of 200 and 50 μm, respectively. The polyurethane performance was superior to the performance of polyvinyl alcohol in terms of higher porosity and better catalytic-solution absorption offering high catalyst active areas. The catalyst prepared from concentrated 10 wt % Ni/Al2O3-MgO (10NAM) slurry had the highest surface area (59.18 m2/g) and the highest metal oxide dispersion (5.65%). These results are relevant to the flow behavior of catalyst slurry which plays a key role in coating the catalyst gel on the polymer template. The thermal decomposition rate used to remove the polymer template from the catalyst structure is proportional to the ceramic foam structure (catalyst support structure). The slow decomposition rate bent and fractured foam-cell struts more than the faster rate. On the other hand, achieving good catalyst dispersion on catalyst supports necessitated a high sintering rate. When sintering was adjusted at a high sintering rate, the metal-particle dispersion was relatively high, around 7.44%, and the surface area of ceramic foam catalysts was 64.61 m2/g. Finally, the catalytic behavior toward hydrogen production through the dry reforming of methane using a fixed-bed reactor was evaluated under certain operating conditions.

Preparation and performance analysis of integrated electric heating hydrogen production foam catalyst

Ni/Al2O3/Foam Electric Heating Catalyst: Mitigating Carbon Emissions and Enhancing Reactor Temperature Uniformity

An Innovative Micro-Channel Catalyst Support with a Micro-Porous Surface for Hydrogen Production Via Methanol Steam Reforming

The Effects of Processing Parameters on the Properties of Micro-Scale Porous Surface for a Micro-Channel Reactor

Preparation of Nickel-Foam-supported Pd/NiO Monolithic Catalyst and Construction of Novel Electric Heating Reactor for Catalytic Combustion of VOCs

Development of Centrifugal Coating Device to Load CuZnZr/γ-Al2O3 Catalyst on Porous Substrates for Methanol Steam Reforming

A Thermally Autonomous Methanol Steam Reforming Microreactor with Porous Copper Foam As Catalyst Support for Hydrogen Production

Design of Induction Heatable Carbon‐Based Foams for Catalysis

Electrically heated monolithic catalyst for in-situ hydrogen production by methanol steam reforming

Fabrication of a Ceramic Foam Catalyst Using Polymer Foam Scrap via the Replica Technique for Dry Reforming

Simulation and enhancement of axial temperature distribution in a reactor filled with in-situ electrically heated structured catalyst

Direct Ink Writing of Hierarchical Porous SiC Ceramics As Catalyst Support for Hydrogen Production

Highly-efficient hydrogen production through the electrification of OB-SiC nickel structured catalyst: Methane steam reforming and ammonia cracking as case studies

Development of centrifugal coating device to load CuZnZr/γ-Al 2 O 3 catalyst on porous substrates for methanol steam reforming

Boosting methylcyclohexane dehydrogenation over Pt-based structured catalysts by internal electric heating

Distributed electrified heating for efficient hydrogen production

Fabrication of γ-Al2O3 Nanoarrays on Aluminum Foam Assisted by Hydroxide for Monolith Catalysts

UV-Laser ablation enhanced Joule-heating catalyst support for electrified MSR in microreactor

Porous Biological Carbon Fiber Foam Combined by Aluminum Phosphate for Enhancing Electric Heating and Electric Thermal Storage Performance

A Study of the Heat Transfer Characteristics of Novel Ni‐foam Structured Catalysts

ZSM-5@ceramic foam composite catalyst derived from spent bleaching clay for continuous pyrolysis of waste oil to produce monocyclic aromatic hydrocarbons