Abstract:Megapores with spherical-like cells connected through windows and high porosities make up catalyst supports in the form of ceramic foams. These characteristics provide significant benefits for catalytic processes that are limited by mass or heat transport. This study focuses on the manufacture of ceramic foam using a polymeric sponge replica process and polymer foams as a template for catalyst supports, which are industrial waste from the packaging sector. To make ceramic foam catalysts, they were dipped in a catalyst solution, followed by a breakdown stage and a sintering process. Experiments focused on determinants that affect the desired characteristics of ceramic foams, such as the types of polymer foams that affect foam morphology, the rheology of catalyst solution that affects catalyst dispersion, and the polymer decomposition rate that affects catalytic performance during dry reforming of the methane process. The cell architectures of polyurethane and polyvinyl alcohol foams are attractive for catalyst support preparation because they have 98-99% porosity and typical cell sizes of 200 and 50 μm, respectively. The polyurethane performance was superior to the performance of polyvinyl alcohol in terms of higher porosity and better catalytic-solution absorption offering high catalyst active areas. The catalyst prepared from concentrated 10 wt % Ni/Al2O3-MgO (10NAM) slurry had the highest surface area (59.18 m2/g) and the highest metal oxide dispersion (5.65%). These results are relevant to the flow behavior of catalyst slurry which plays a key role in coating the catalyst gel on the polymer template. The thermal decomposition rate used to remove the polymer template from the catalyst structure is proportional to the ceramic foam structure (catalyst support structure). The slow decomposition rate bent and fractured foam-cell struts more than the faster rate. On the other hand, achieving good catalyst dispersion on catalyst supports necessitated a high sintering rate. When sintering was adjusted at a high sintering rate, the metal-particle dispersion was relatively high, around 7.44%, and the surface area of ceramic foam catalysts was 64.61 m2/g. Finally, the catalytic behavior toward hydrogen production through the dry reforming of methane using a fixed-bed reactor was evaluated under certain operating conditions.

Design of Induction Heatable Carbon‐Based Foams for Catalysis

Methanol to Propylene over Foam SiC-Supported ZSM-5 Catalyst: Performance of Multiple Reaction–Regeneration Cycles

Preparation and performance analysis of integrated electric heating hydrogen production foam catalyst

Preparation of Nickel-Foam-supported Pd/NiO Monolithic Catalyst and Construction of Novel Electric Heating Reactor for Catalytic Combustion of VOCs

Synthesis of Micro- and Mesoporous Carbon Foams with Nanodispersed Metals for Adsorption and Catalysis Applications

Catalytic Conversion of Ethanol with Conventional and Ohmic Heating in Comparison

Development of Centrifugal Coating Device to Load CuZnZr/γ-Al2O3 Catalyst on Porous Substrates for Methanol Steam Reforming

Preparation of γ-Al2O3/α-Al2O3 ceramic foams as catalyst carriers via the replica technique

Fabrication of a Ceramic Foam Catalyst Using Polymer Foam Scrap via the Replica Technique for Dry Reforming

A Study of the Heat Transfer Characteristics of Novel Ni‐foam Structured Catalysts

Industrially Potential MoVNbTeOx@FoamSiC Structured Catalyst for Oxidative Dehydrogenation of Ethane

Composite materials made from glass microballoons and ceramic nanofibers for use as catalysts and catalyst supports

MOF-based heterogeneous catalysis in continuous flow via incorporation onto polymer-based spherical activated carbon supports

An Emerging Strategy in Sequential Synthesis of Catalyst and Carbon Nanotube Foams by Employing a Chemical Vapor Deposition Procedure: Structural Evaluation and Growth Mechanism

Catalyst Deactivation of Rh-Coated Foam Monolith for Catalytic Partial Oxidation of Methane

Ni‐Al2O3/Ni‐foam catalyst with enhanced heat transfer for hydrogenation of CO2 to methane

Heat transfer intensification in compact tubular reactors with cellular internals: A pilot-scale assessment of highly conductive packed-POCS with skin applied to the Fischer-Tropsch synthesis

Utilising magnetite and heteropoly acid to modify silica foam and consider catalytic activity for esterification and transesterification procedure

Synthesis of carbon foam covered with carbon nanofibers as catalyst support for gas phase catalytic reactions

Synthesis of Nano-catalysts by Induction Suspension Plasma Technology (SPS) for Fischer–Tropsch Reaction

Carbon Nanotube Modified Ceramic Foams As Structured Palladium Supports for Polystyrene Hydrogenation