Abstract:A two-step time-to-digital converter (TDC) is designed for the high-precision time measurement of the DIRC-like TOF (DTOF) detector at the Super Tau-Charm Facility (STCF). Extending the measurement range by Nutt's method, the TDC clock cycle is interpolated with two voltage-controlled tapped delay lines (TDL) connected by a dual-slope time amplifier (TA). By amplifying the residue from the first-step TDL-based interpolation with the TA and measuring it with the second TDL, the TDC resolution is significantly improved to sub-gate delay. Since the residue is extracted by a new method without the need of TA duplication or delay insertion, the TDC power consumption and conversion time are effectively reduced. By adopting the improved TA circuit into the TDC with a high gain, adjustable output offsets, and good linearity, the TDC measurement precision is guaranteed. In addition, a new DLL structure is proposed to stabilize the TDL against process, voltage, and temperature (PVT) variations with less power consumption. Benefiting from the proposed residue extraction method and DLL structure, the TDC exhibits low power consumption. To verify the TDC design, a prototype chip with two TDC channels is fabricated in GlobalFoundries (GF) 180 nm CMOS technology for performance evaluation. With a system clock of 150 MHz, it has a resolution (LSB) of 16.5 ps and a maximum sample rate of 6 MS/s. The differential nonlinearity (DNL) error ranges from - 0.98 LSB to 0.87 LSB and the integral nonlinearity error (INL) ranges from- 4.21 LSB to 2.83 LSB. With a bin-by-bin calibration method, the measured TDC precision is 12.1 ps on average within the 0-20 ns time interval measurement range. In addition, the TDC has low temperature sensitivity and does not require recalibration within a 20 C-degrees temperature range. Each TDC channel consumes 434 mu W power at 1 MS/s sample rate. The test results confirm that the proposed TDC can achieve high precision with a moderate sample rate and low power consumption without highly scaled technologies, which can meet the requirements of the DTOF detector at STCF.

A 0.013mm2 3.2ns Input Range 10-bit Cyclic Time-to-Digital Converter Using Gated Ring Oscillator With Phase Domain Reset in 65nm CMOS

A 50-Ps Gated VCRO-Based TDC with Compact Phase Interpolators for Flash LiDAR

A Two-Step Time-to-Digital Converter with 5.6ps Resolution and 1 - 4255μs Measurement Range

A Multi-Path Gated Ring Oscillator Based Time-To-Digital Converter In 65 Nm Cmos Technology

A 0.004-Mm2 3.65-Mw 7-Bit 2-Gs/s Single-Channel GRO-Based Time-Domain ADC Incorporating Dead-Zone Elimination and On-Chip Folding-Offset Calibration in 28-Nm CMOS

An all-digital low-power, low-frequency GRO-based time to digital converter for biomedical applications

A 71Ps-Resolution Multi-channel CMOS Time-to-Digital Converter for Positron Emission Tomography Imaging Applications

Recent Developments and Design Challenges of High-Performance Ring Oscillator CMOS Time-to-Digital Converters

A 12bit 39ps Two-Step Time-to-Digital Converter in 40nm CMOS

A 49.5 Μw Multichannel Time-to-Digital Converter with 2D/3D Imaging Fusion for APD LiDAR Sensors

A Wide Dynamic Range and Low Bit Error Pixel TDC Suitable for Array Application.

A CMOS Time-to-digital Converter for Multi-Voltage Threshold Method in Positron Emission Tomography

A 10ps 500MS/s two-channel Vernier TDC in 0.18um CMOS technology

A Low-Power Gateable Vernier Ring Oscillator Time-to-Digital Converter for Biomedical Imaging Applications.

A 12 Ps Precision Two-Step Time-to-Digital Converter Consuming 434 $\mu$ W at 1 MS/s in 180 Nm CMOS with a Dual-Slope Time Amplifier

A 0.5-bit step multi-resolution adjustable-input range reconfigurable noise-shaping TDC using multi-step quantizer gated-ring oscillators

A High-Resolution Multi-Channel Time-To-Digital Converter (Tdc) For High-Energy Physics And Biomedical Imaging Applications

A 10ps 500mhz Time-to-digital Converter in 0.18&#x03bc;m CMOS Technology for ADC

A Novel Time-to-Digital Converter Based on Low-Jitter Phase-Locked Loop

A 1.3mW 8-bit Two-step Time-to-Digital Converter

A 10-Bit 563-Fs Step Constant-Slope Digital-to-Time Converter in 40-Nm CMOS with Nonlinearity Cancellation and Range Extension Techniques