Abstract:This study focuses on the effects of hybrid reinforcement consisting of nanosized particles of Palm Sprout Shell Ash (PSSA) and silicon carbide (SiC) on the mechanical and tribological properties of the Al-Cu-Mg alloy. Hybrid reinforced composites with different weight percentages of SiC and PSSA (0:0, 0:4, 1:3, 2:2, and 4:0 wt%) were prepared using the ultrasonic-assisted bottom-poured stir casting technique. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) were used to characterize the hybrid composite made of Al-Cu-Mg alloy. The optical and SEM microstructural analyses demonstrated an even distribution of SiC and PSSA nanosize reinforcements within the matrix. The EDS analysis revealed SiC and PSSA reinforcement particles in the composite. The mechanical properties (tensile, flexural, and impact strength) and wear properties (wear rate and coefficient of friction) of the composites and alloys were evaluated according to the ASTM standards. The hybrid reinforced composites outperformed the base alloy. Among all composites, the 2:2 wt% SIC and PSSA hybrid-reinforced composites exhibited a significant enhancement in both tensile and flexural strength, with a 22.64% and 27.64% increase in strength, respectively. However, the inclusion of these reinforcements led to a reduction in the ductility and impact strength of the Al-Cu-Mg alloy composite. The 0:4 wt% SiC- and PSSA-reinforced composites experienced the largest reductions in ductility and impact strength, with decreases of 47.67% and 4.38%, respectively. For the 2:2 wt% SiC and PSSA composites, these reductions were 23.64% and 3.19%, respectively. The SEM analysis of the fractured surfaces of the composites tested for mechanical properties revealed evidence of both ductile and brittle fracture mechanisms in the tensile, flexural, and impact tests. The wear behaviour of the prepared samples was evaluated, and all composites exhibited superior performance compared with the base alloy, demonstrating adhesive and abrasive wear mechanisms and varying friction coefficients. Among all the composites, the 2:2 wt% SiC- and PSSA-reinforced composites exhibited high wear resistance and a lower coefficient of friction than the other fabricated composites.

Studies on tribological behavior of aluminum hybrid composites strengthened with MoS2 and wheat husk ash

Dry sliding wear behaviour of AA6082/BN/Mos2 hybrid metal matrix composites synthesized using stir casting process

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Empirical investigation on controlled porosity level and dry sliding wear behavior of Al7075-(T6) doped with SiC+MoS2 based hybrid composites via advanced vacuum-assisted stir casting

Dry Sliding Wear Studies on Sillimanite and B4C Reinforced Aluminium Hybrid Composites Fabricated by Vacuum Assisted Stir Casting Process

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Taguchi optimized wear and self-lubricating properties of Al-alloy composite reinforced with hybrid B 4 C–MoS 2 particulates

Dry Sliding Wear Behavior of Copper Matrix Composites Enhanced with TiO2 and MoS2 Hybrids

Synergistic approach to tribological characterization of hybrid aluminum metal matrix composites with ZrB2 and fly ash: Experimental and predictive insights

Investigation of Tribological Behavior of a Novel Hybrid Composite Prepared with Al-Coconut Shell Ash Mixed with Graphite

Tribological Behavoiur of Silicon Carbide/ Rice Husk ash Reinforced Al7075 Hybrid Composites Using Optimization Techniques

Dry sliding wear and viscoelastic performance of aluminum-based hybrid composites reinforced with SiC and metallic glass particles

Synthesis and wear characterization of Al7075/molybdenum disulfide/zirconium diboride hybrid compositesSynthese und Verschleißcharakterisierung von hybriden Al7075/MoS2/ZrB2‐Verbundwerkstoffen

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

A Study on Mechanical and Tribological Properties of Aluminum 7075 MMCS Reinforced with Silicon Carbide and Coconut Husk by Powder Metallurgy Process

Tribological Investigation of Composite MoS2-TiO2-ZrO2 Coating Material by Response Surface Methodology Approach

Effect of SiC Weight Percentage on Tribological Characteristics of Al7075/SiC Composites

Mechanical and dry sliding tribological characteristics of aluminium matrix composite reinforced with high entropy alloy particles

Effect of MoS2 on the Tribological Properties of in Situ Fe3Al-20 Wt% Al2O3-4 Wt% Cr Composites

Influence of Particle Size on Microstructure and Sliding Wear Response of Fly Ash and Rice Husk Ash Reinforced Al6061 MMCs

Corrigendum: A study on the effects of hybrid (SIC- PSSA) nano sized reinforcement on mechanical and tribological behaviour of Al alloy-based metal matrix composite produced by ultrasonic assisted stir casting (2024 Mater. Res. Express 11 075010)