Abstract:Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, Ahead of Print. Aluminum alloys feature impressive levels of strength, ductility, castability, wear resistance, and corrosion resistance, making them highly advantageous for the aviation and automotive industries. This study investigates the dry wear performance of hybrid nanocomposites (HNCs) produced using Al6061 as the matrix, with nano-fly ash (FA) and nano-yttrium oxide (Y2O3) as reinforcing agents, utilizing the stir-casting method. The weight percentage (wt-%) of FA was fixed at 4 wt-%, while the Y2O3 varied from 1 wt-% to 3 wt-%. The specimens were prepared following ASTM-G99 standards and tested using a pin-on-disc apparatus with an E31 steel disc under four different loads: 10 N, 20 N, 30 N, and 40 N. It has been observed that wear rate has been increased with the increase in the applied load. The maximum wear rate has been recorded for the base Al6061 alloy as 5.63 × 10−4 mm3/N-m at 40 N load due to its lower wear resistance and less hardness value. The addition of reinforcement particles in the base alloy results in the grain refinement and improvement in the load-bearing capacity. It has been found that at 40 N load, the Al-6061 alloy reinforced with (4 wt-% FA + 3 wt-% Y2O3) is 56.83% superior in terms of wear resistance (2.43 × 10−4 mm3/N-m) as compared to Al6061 base alloy. The hybrid nano-composite containing 4 wt-% FA + 3 wt-% Y2O3 showed the highest value of microhardness as 123.2 HV, which is 136% higher than that of base alloy due to the higher load-bearing characteristics of the reinforcement particles. Scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) have been employed to analyze both unworn and worn surfaces, revealing uniform dispersion of reinforcement particles, the formation of an oxide layer, micro-pitting, wear debris, and material delamination. Grain refinement has been examined using the line intercept method (ASTM E1382-97), and X-ray diffraction (XRD) confirmed the elemental composition of the nano-reinforcements.

Influence of Particle Size on Microstructure and Sliding Wear Response of Fly Ash and Rice Husk Ash Reinforced Al6061 MMCs

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Desirability based multiobjective optimisation of abrasive wear and frictional behaviour of aluminium (Al/3.25Cu/8.5Si)/fly ash composites

Enhancing wear resistance of aluminum 6061 composites with fly ash: A sustainable approach for industrial applications

Mathematical Modeling and Analysis of Tribological Properties of AA6063 Aluminum Alloy Reinforced with Fly Ash by Using Response Surface Methodology

Dry sliding wear characteristics of hybrid aluminum alloy with nano-fly ash and nano-yttrium oxide

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis

Metallographic Study and Sliding Wear Optimization of Nano Si3N4 Reinforced High-Strength Al Metal Matrix Composites

Tribological Behavoiur of Silicon Carbide/ Rice Husk ash Reinforced Al7075 Hybrid Composites Using Optimization Techniques

Investigating the Impact of Dual-Range Iron Slag Particles-Reinforced Aluminum Composite for Dry Sliding Applications

Physical, Mechanical, and Tribological Properties of Industrial Waste Fly Ash Reinforced AA5083 Composites Fabricated by Stir Casting Process

Influence of wear parameters on friction performance of A356 aluminum – graphite/ granite particles reinforced metal matrix hybrid composites

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Tribological characteristics of AA7075 composites reinforced with rice husk ash and carbonized eggshells

Development, mechanical characterization and analysis of dry sliding wear behavior of AA6082–Metakaolin metal matrix composites

Mechanism of abrasive wear of Al-Si hypoeutectic alloycontaining 5 vol% fly ash

Experimental Investigations on Microstructure, Mechanical and Wear Behavior Under Dry Sliding of Al6061 with Particulate-Reinforced SiC and TiB2 Metal Matrix Composite Developed by Stir Casting

Enhanced mechanical behaviour and grain characteristics of aluminium matrix composites by cold rolling and reinforcement addition (Rice husk ash and Coal fly ash)

Experimental Investigation of Friction and Wear Behavior of AL7075-TiO2-B4C using RSM, ANN and Desirability Function

Mechanical properties and fractography of SiC and fly ash particulates reinforced Al2024 alloy aerospace metal composites