Abstract:This study focuses on the effects of hybrid reinforcement consisting of nanosized particles of Palm Sprout Shell Ash (PSSA) and silicon carbide (SiC) on the mechanical and tribological properties of the Al-Cu-Mg alloy. Hybrid reinforced composites with different weight percentages of SiC and PSSA (0:0, 0:4, 1:3, 2:2, and 4:0 wt%) were prepared using the ultrasonic-assisted bottom-poured stir casting technique. Scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDS) were used to characterize the hybrid composite made of Al-Cu-Mg alloy. The optical and SEM microstructural analyses demonstrated an even distribution of SiC and PSSA nanosize reinforcements within the matrix. The EDS analysis revealed SiC and PSSA reinforcement particles in the composite. The mechanical properties (tensile, flexural, and impact strength) and wear properties (wear rate and coefficient of friction) of the composites and alloys were evaluated according to the ASTM standards. The hybrid reinforced composites outperformed the base alloy. Among all composites, the 2:2 wt% SIC and PSSA hybrid-reinforced composites exhibited a significant enhancement in both tensile and flexural strength, with a 22.64% and 27.64% increase in strength, respectively. However, the inclusion of these reinforcements led to a reduction in the ductility and impact strength of the Al-Cu-Mg alloy composite. The 0:4 wt% SiC- and PSSA-reinforced composites experienced the largest reductions in ductility and impact strength, with decreases of 47.67% and 4.38%, respectively. For the 2:2 wt% SiC and PSSA composites, these reductions were 23.64% and 3.19%, respectively. The SEM analysis of the fractured surfaces of the composites tested for mechanical properties revealed evidence of both ductile and brittle fracture mechanisms in the tensile, flexural, and impact tests. The wear behaviour of the prepared samples was evaluated, and all composites exhibited superior performance compared with the base alloy, demonstrating adhesive and abrasive wear mechanisms and varying friction coefficients. Among all the composites, the 2:2 wt% SiC- and PSSA-reinforced composites exhibited high wear resistance and a lower coefficient of friction than the other fabricated composites.

Mechanical properties and fractography of SiC and fly ash particulates reinforced Al2024 alloy aerospace metal composites

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Experimental investigation of material properties of Al-Sic-fly ash composite

Experimental Investigation on Metal Matrix Nanocomposite: Aluminium Alloy 6061 and 7075 with SiC and Fly Ash

Effect of Microstructure on Mechanical Behaviors of Al6061 Metal Matrix Composite Reinforced with Silicon Nitride (Si3N4) and Silicon Carbide (SiC) Micro Particles

Influence of Nano-Hybrid Reinforcements on the Improvement Strength, Thermal Expansion and Wear Properties of Cu–SiC–Fly Ash Nanocomposites Prepared by Powder Metallurgy

Effect of Si3N4 Ceramic Particulates on Mechanical, Thermal, Thermo-Mechanical and Sliding Wear Performance of AA2024 Alloy Composites

Effect of SiC Content on Mechanical and Tribological Properties of Al2024-SiC Composites

Development and wear behavior investigation on aluminum-7075/B4C/fly ash metal matrix composites

Mechanical and Micro-Structural Behavior of Lignite Coal Based Fly-Ash and Microsphere Reinforced Al 6061 Metal Matrix Composite

Effects of Silicon Carbide and Tungsten Carbide in Aluminium Metal Matrix Composites

Influence of Particle Size on Microstructure and Sliding Wear Response of Fly Ash and Rice Husk Ash Reinforced Al6061 MMCs

Analysis on Mechanical Behaviour of Binary and Hybrid Al2014 Metal Matrix Composites

A Study On The Effects Of Hybrid (Sic- Pssa) Nano Sized Reinforcement On Mechanical And Tribological Behaviour Of Al Alloy-Based Metal Matrix Composite Produced By Ultrasonic Assisted Stir Casting

Effect of forging on mechanical properties of rice husk ash-silicon carbide reinforced Al1100 hybrid composites

Experimental investigation in enhancing the mechanical, wear and corrosion resistance properties of Al6061-SiC-NSA composites fabricated using stir casting process.

Corrigendum: A study on the effects of hybrid (SIC- PSSA) nano sized reinforcement on mechanical and tribological behaviour of Al alloy-based metal matrix composite produced by ultrasonic assisted stir casting (2024 Mater. Res. Express 11 075010)

Investigation on Mechanical and Fracture Behavior of Magnesium Composite Reinforced With Hybrid Fly Ash Particulates Synthesized via Friction Stir Processing Route

Investigation of Mechanical Properties of Aluminium 6061-Silicon Carbide, Boron Carbide Metal Matrix Composite

Mechanical and Wear Behaviour of Nano-Fly Ash Particle-Reinforced Mg Metal Matrix Composites Fabricated by Stir Casting Technique

Micro-mechanical and tribological behavior of Al/SiC/B4C/CNT hybrid nanocomposite