Abstract:The aluminum fly ash metal matrix composites (MMCs) find important applications in automobile and aerospace where high strength and modulus is important. The fly ash by product of coal burning is drawing lot of attention as reinforcement for MMCs due to its low cost and reduction in environmental pollution. The ash particles, generally being hollow in nature, display lower densities while oxides present as constituents make them possess high modulus and strength thereby enhancing specific strength and stiffness along with lower densities compared to many metal based systems. The uses of MMCs are impeded in critical applications due to its low fracture toughness as compare to metals. LEFM (Linear Elastic Fracture Mechanics) has been used by researchers to characterize the plane strain fracture toughness using various specimen geometries and notches. However there were very few studies using EPFM (Elastic Plastic Fracture Toughness) are reported in open literature. In the present paper the influences of weight fraction of fly ash reinforcement on hardness, tensile strength and fracture toughness have been evaluated. Hardness of aluminium fly ash metal matrix composites increases with the addition of fly ash particulate reinforcement. However the tensile strength and fracture toughness KIC and JIC of the aluminum fly ash composite decreases that of base alloy. The fracture toughness of AA2024 varied between 17-18 MPa√�� as compared to 21 MPa√�� for remelted base alloy AA2024, which is consistent with the reported data. The JIC fracture toughness of AA2024 fly ash composites varied between 6-15 KJ/m² as compared to 25 KJ/m² for the re melted base alloy AA2024. The load and COD plot shows hysteresis loop in loading and unloading compliance curve. This hysteresis loop is indicative of crack closure due to fly ash particles. The reason for crack closure may be surface roughness resulting from reinforcement particles in the composites. The fracture behavior and micro-mechanism of failure in base alloy and composites have been observed under SEM and optical microscopy.

Mechanical and Micro-Structural Behavior of Lignite Coal Based Fly-Ash and Microsphere Reinforced Al 6061 Metal Matrix Composite

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

MMCs with Controlled Non-Uniform Distribution of Submicrometre Al2O3particles in 6061 Aluminium Alloy Matrix

Fracture Toughness of AA2024 Aluminum Fly Ash Metal Matrix Composites

Experimental Investigation on Metal Matrix Nanocomposite: Aluminium Alloy 6061 and 7075 with SiC and Fly Ash

Experimental investigation of material properties of Al-Sic-fly ash composite

Mechanical properties and fractography of SiC and fly ash particulates reinforced Al2024 alloy aerospace metal composites

Development and wear behavior investigation on aluminum-7075/B4C/fly ash metal matrix composites

Influence of Particle Size on Microstructure and Sliding Wear Response of Fly Ash and Rice Husk Ash Reinforced Al6061 MMCs

Physical, Mechanical, and Tribological Properties of Industrial Waste Fly Ash Reinforced AA5083 Composites Fabricated by Stir Casting Process

Evaluation of Mechanical and Thermal Properties of Aluminium-7475 Reinforced with Graphite and Fly ash

Mechanical and Wear Behaviour of Nano-Fly Ash Particle-Reinforced Mg Metal Matrix Composites Fabricated by Stir Casting Technique

The effect of reinforcements on mechanical properties of A7005 hybrid MMCs

Investigation on Mechanical and Fracture Behavior of Magnesium Composite Reinforced With Hybrid Fly Ash Particulates Synthesized via Friction Stir Processing Route

Investigation on Mechanical Behavior of Al6061- Coconut Shell Ash- Granite Dust Reinforced Hybrid Metal Matrix Composites Manufactured using Stir Casting Technique

Effect of Heat Treatment on Mechanical Properties of Aluminium alloy-Fly ash Metal Matrix Composite

Enhancing wear resistance of aluminum 6061 composites with fly ash: A sustainable approach for industrial applications

Investigation of Mechanical Properties of Aluminium 6061-Silicon Carbide, Boron Carbide Metal Matrix Composite

Performance analysis and mechanical behavior of aluminum metal matrix composite

Microstructural Characterization, Mechanical And Wear Behaviour Of Al2024-B4C Composites For Aerospace Applications

Developments in the aluminum metal matrix composites reinforced by micro/nano particles – A review