Abstract:In this research work, hybrid AA2024–SiC/Si3N4 alloy composites were designed and prepared through a semi-automatic stir casting route, following industrial procedure. The ceramic (SiC/Si3N4) particulates were reinforced in the complementary manner (0–4 wt% @ step of 1%), leading to five composite specimens, namely CN04, CN13, CN22, CN31, and CN40. The samples of each composition were analyzed for their physical, mechanical, thermal conductivity, fracture toughness, and tribological behavior (steady-state sliding wear analysis) adopting ASTM standards. The Taguchi methodology was applied to optimize experimental simulations and input operating variables (like sliding velocity, sliding distance, normal load, composition, and environment temperature) with ANOVA. Worn-out surface micrograph studies were performed using a scanning electron microscope (SEM) and energy-dispersive X-ray spectroscopy (EDS) to understand wear mechanisms and elemental presence/dispersion over the surface. Further, a decision-making tool like a hybrid AHP-TOPSIS method was applied to rank the hybrid alloy composites based upon performance measures. The hybrid alloy composites shows some peculiar properties like density ~ 2.495–2.772 g/cc, voids content ~ 0.63–10.49%, Rockwell hardness (HRB) ~ 76.6 to 92.8 HRB, tensile strength ~ 191–277 MPa, flexural strength ~ 291–419 MPa, Impact strength ~ 24–100 J, thermal conductivity ~ 141–152 W/mK, fracture toughness ~ 6–41 MPa √m. Taguchi’s factorial design of the experiment shows an error of 3.5% for the S/N ratio of wear rate that validates the robustness of the experiential design. The wear rate and friction coefficient improve with sliding velocity irrespective of composition across the formulation. Further, it has been found that CN22 hybrid alloy composite having an equal amount of both ceramics tends to optimize the overall physical and mechanical properties along with steady-state sliding behavior, which is in-tune-with the results of ranking obtained hybrid AHP-TOPSIS method. The sensitivity analysis of performance criteria gives robust/stable ranking order whenever the criteria’s weight varies within ± (10–15)%.

Taguchi optimized wear and self-lubricating properties of Al-alloy composite reinforced with hybrid B 4 C–MoS 2 particulates

Empirical investigation on controlled porosity level and dry sliding wear behavior of Al7075-(T6) doped with SiC+MoS2 based hybrid composites via advanced vacuum-assisted stir casting

Mechanical Characteristics and Wear Behaviour of Al/SiC and Al/SiC/B4C Hybrid Metal Matrix Composites Fabricated Through Powder Metallurgy Route

Exploring tribological properties in the design and manufacturing of metal matrix composites: an investigation into the AL6061-SiC-fly ASH alloy fabricated via stir casting process

Studies on tribological behavior of aluminum hybrid composites strengthened with MoS2 and wheat husk ash

Dry sliding wear behaviour of AA6082/BN/Mos2 hybrid metal matrix composites synthesized using stir casting process

Influence of B4C on Dry Sliding Wear Behavior of B4C/Al–Mg–Si Composites Synthesized via Powder Metallurgy Route

Study on Dry Sliding Wear and Friction Behaviour of Al7068/Si3N4/BN Hybrid Composites

Experimental Investigation of Friction and Wear Behavior of AL7075-TiO2-B4C using RSM, ANN and Desirability Function

Multi-response optimisation of wear parameters of B4C reinforced Al-Fe-Si composites: Using Taguchi-grey relational analysis

Mechanical Properties and Tribological Behavior of Al6061–SiC–Gr Self-Lubricating Hybrid Nanocomposites

Investigation on the effect of SiC and TiB2 ceramic particles on mechanical and tribological properties of Al7075 hybrid metal matrix composites prepared through conventional stir casting technique

Micro-mechanical and tribological behavior of Al/SiC/B4C/CNT hybrid nanocomposite

Parametric Optimization and Ranking Analysis of Hybrid AA2024–SiC/Si3N4 Alloy Composites Based on Mechanical and Sliding Wear Performance

Effect of B4C and SiC nanoparticle reinforcement on the wear behavior and surface structure of aluminum (Al6063-T6) matrix composite

Metallographic Study and Sliding Wear Optimization of Nano Si<sub>3</sub>N<sub>4</sub> Reinforced High-Strength Al Metal Matrix Composites

Optimization of Tribological Behaviour of Ti6Al4V/TiB2/TiC Hybrid MMCs Using Response Surface Methodology

Dry sliding wear and viscoelastic performance of aluminum-based hybrid composites reinforced with SiC and metallic glass particles

Influence of Particle Size on Microstructure and Sliding Wear Response of Fly Ash and Rice Husk Ash Reinforced Al6061 MMCs

Mechanical and wear behavior of Al 7075/Al2O3/SiC/mg metal matrix nanocomposite by liquid state process

Experimental tribological and mechanical behavior of aluminium alloy 6061 composites incorporated ceramic particulates using Taguchi analysis